Today's Message Index:
----------------------
1. 12:13 PM - Re: Re: Flap switch (Peter Laurence)
2. 12:51 PM - Re: Re: Flap switch (George, Neal E Capt MIL USAF 605TES/TSI)
3. 03:47 PM - Re: Flap switch (Robert L. Nuckolls, III)
4. 07:07 PM - AUDIO ISOLATION AMP PC BOARD (RV4WGH@aol.com)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Eric the subject is a flap motor not a MAC servo.
Peter Laurence
----- Original Message -----
From: "Eric M. Jones" <emjones@charter.net>
Sent: Tuesday, July 17, 2007 10:35 AM
Subject: AeroElectric-List: Re: Flap switch
> <emjones@charter.net>
>
> I think what you need is what I sell lots of--the True Servo Conversion
> for MAC/RACs. TSCMR. This is a teeny module that converts the external
> position signal that you get from a voltage divider potentiometer or even
> a bank of push buttons to control a MAC or RAC trim box.
>
> See: http://tinyurl.com/2qo222
>
> These are the parts they left out of the trim box that would have made it
> a servo. This also solves the problem of how to connect all those tiny
> trim box wires.
>
> --------
> Eric M. Jones
> www.PerihelionDesign.com
> 113 Brentwood Drive
> Southbridge, MA 01550
> (508) 764-2072
> emjones@charter.net
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=124343#124343
>
>
>
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Peter -
If I understand the descriptions...
Eric's TSCMR, when combined with RAC's position sensor (attached to the
flap mechanism), can be configured to approximate the Cessna-style
set-forget flap switch.
************************
Eric the subject is a flap motor not a MAC servo.
Peter Laurence
>
> I think what you need is what I sell lots of--the True Servo
Conversion
> for MAC/RACs. TSCMR. This is a teeny module that converts the external
> position signal that you get from a voltage divider potentiometer or
even
> a bank of push buttons to control a MAC or RAC trim box.
>
> See: http://tinyurl.com/2qo222
>
> These are the parts they left out of the trim box that would have made
it
> a servo. This also solves the problem of how to connect all those tiny
> trim box wires.
>
> --------
> Eric M. Jones
> www.PerihelionDesign.com
> 113 Brentwood Drive
> Southbridge, MA 01550
> (508) 764-2072
> emjones@charter.net
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
At 06:11 PM 7/17/2007 -0400, you wrote:
>
>I have a genuine Cessna 150 switch. I just need to find out if it can
>be wired into the system instead of using the supplied switch from Ray
>Allen that was with the servo..
Cessna had a LOT of different flap controls. Need a photo,
p/n, perhaps a schematic of the system it came out of.
Baring that detail of data, you can send me the switch
and I'll deduce its suitability to task.
Bob . . .
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | AUDIO ISOLATION AMP PC BOARD |
Bob,
I ordered a PC board on July 6 and received a email confirmation that I
would be getting an email with instructions on how to make payment. Nothing yet.
Have tried to reach you via phone, email and email via your web site.
Do you still supply the boards?
Regards,
Wally Hunt
Rockford, IL
RV-4 Finishing Kit
815-262-3153
************************************** Get a sneak peek of the all-new AOL at
http://discover.aol.com/memed/aolcom30tour
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|