Today's Message Index:
----------------------
1. 04:08 AM - Re: AMR-350 pin-out (Michael Hinchcliff)
2. 04:42 AM - Shadin ADC-200 (Don Curry)
3. 04:53 AM - Re: Alternator Breaker Pop (DaveG601XL)
4. 05:05 AM - Re: Strippers are all spoken for. (Bret Smith)
5. 04:55 PM - Two New Lists Added to the Matronics Lineup! (Matt Dralle)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: AMR-350 pin-out |
There it is! I was looking in the wrong place. Thanks Bob!
Do not Archive.
Michael H.
----- Original Message -----
From: "Robert L. Nuckolls, III" <nuckolls.bob@cox.net>
Sent: Friday, March 28, 2008 10:51 PM
Subject: Re: AeroElectric-List: AMR-350 pin-out
> <nuckolls.bob@cox.net>
>
> At 08:58 PM 3/28/2008 -0500, you wrote:
>
>>Hey guys, does anybody out there have an electronic copy of the Collins
>>Audio Panel (AMR-350) pin-out diagram? If so, can you share it with me?
>>Thanks!
>>
>>Michael H.
>>
>
> See:
>
> http://www.aeroelectric.com/Installation_Data/
>
> Bob . . .
>
>
>
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
I'm installing a Shadin ADC-200 to display air-data/fuel-flow on my
Garmin
GPS-400. Does anybody know if the ADC-200 will accept OAT information
from
my already-installed Davtron M307FC or will I have to install a separate
OAT
probe? Also, does anybody know which fuel flow sensors are compatible
with
the ADC-200 (my aircraft has a Lycoming O-360 and a 28v electrical
system).
Thanks, Don
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Alternator Breaker Pop |
Bob,
I have purchased all of my electrical parts since September so barring any of it
sitting on B&C's shelves for a long time, everything should be fairly new.
I have not had the chance to go over the system wire-by-wire yet. I will report
back after I have had the chance.
Thanks,
--------
David Gallagher
601 XL, all major assemblies complete. Have run the engine and am starting final
assembly.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=173387#173387
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Strippers are all spoken for. |
Geez, I go out of town for a few days and the List turns to debauchery!
Bob, you better hope Dee doesn't hear about this!
Bret Smith
RV-9A N16BL
Blue Ridge, Ga
www.FlightInnovations.com
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Two New Lists Added to the Matronics Lineup! |
Dear Listers,
I've added two new Email Lists to the Matronics List and Forum lineup today. These
include the Rans-List and RV12-List. Please surf over to the Matronics List
Subscription page and sign up for these new Lists if they are of interest
to you:
http://www.matronics.com/subscribe
Full support on the Forums, List Browse, Archives, etc. is available.
Rans-List:
http://www.matronics.com/Navigator?Rans-List
RV12-List
http://www.matronics.com/Navigator?RV12-List
Best regards,
Matt Dralle
Matronics Email List Administrator
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|