Today's Message Index:
----------------------
1. 09:02 AM - Re: LED WigWag with B&C SSF-1 (gregmchugh)
2. 09:41 AM - Re: Re: LED WigWag with B&C SSF-1 (Robert L. Nuckolls, III)
3. 10:44 AM - Next generation wig-wag controller for LED lamps (Robert L. Nuckolls, III)
4. 12:11 PM - Re: Troubleshooting Field Breaker (Jim P)
5. 06:27 PM - Trade my 5a CB's for 7.5a (jonlaury)
6. 09:04 PM - Next generation wig-wag controller for LED lamps (Michael Ashura)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: LED WigWag with B&C SSF-1 |
I have been considering the Perihelion Wig-Wag to use with Teledyne LED Landing/Taxi
lights. I will be interested in other options for the Wig-Wag module...
Wig-Wag
http://www.periheliondesign.com/wigwagmnl.htm
LED Lights
http://www.aircraftspruce.com/catalog/elpages/teledynelandinglight.php
Greg McHugh
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=370030#370030
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: LED WigWag with B&C SSF-1 |
At 11:01 AM 4/4/2012, you wrote:
>
>I have been considering the Perihelion Wig-Wag to use with Teledyne
>LED Landing/Taxi lights. I will be interested in other options for
>the Wig-Wag module...
That one works and is, no doubt, suited to LED
lighting fixtures
Bob . . .
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Next generation wig-wag controller for LED lamps |
At 06:19 PM 3/30/2012, you wrote:
>
>Bob, can I wire two LED landing and taxi lights per Page 3.0 (Ref DE
>12/15/11) but using a single switch (already installed and labeled
>in unflown RV-6) as shown on Page 3.0 from 2003? Thank you
Give me a few days on this. It occurs to me that
I've been twisting what WAS a good system for
incandescent lamps into a pretzel in search
of the elegant solution for LED lamps.
---------------------------------------
As promised, I spend some time considering the
ingredients that go into an alternative recipe
for success. I began with the following design
goals:
All solid state
Stand off 20V bus for 1 second or more
Simple switching that does NOT require progressive
transfer switch to achieve OFF/WW/ON operation
of lights.
Suitable for LED landing light fixtures
Minimum parts count.
While plying the asphalt between here and Wichita
I sifted through the pieces and parts. Here's
a first pass at the idea.
http://tinyurl.com/6t7zry2
This device could be fabricated from surface mount
parts and totally contained inside a 15-pin, d-sub
housing for an end product that looks like this.
Emacs!
This circuit also lends itself to a DIY effort with
thru-hole parts mounted on a perf board.
Mike, if you already have a 2-10 switch installed,
it can be wired to function with this controller.
Bob . . .
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Troubleshooting Field Breaker |
Thanks Joe, I'll run that test when I'm back out at the airport.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=370039#370039
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Trade my 5a CB's for 7.5a |
I just purchased and installed two 5a breakers where 7.5a were called for. Can't
return them so if you have 2x7.5a and need 5's, raise your hand.
I have the new smaller, green ones from Klixon
Thanks,
John
see http://www.aircraftspruce.com/catalog/elpages/klixon2tc5.php
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=370061#370061
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Next generation wig-wag controller for LED lamps |
Bob, thank you for the schematic. I guess this is the part where the "education"
part comes in with my project. The "U" devices already have my curiosity...
BTW, how does a person see the picture where the Emacs! occurs?
Mike
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|