Today's Message Index:
----------------------
1. 12:20 PM - Re: A200/Flightcom 403 radio not transmitting- plane grounded!! (SIDESLIP)
2. 12:42 PM - Re: Re: A200/Flightcom 403 radio not transmitting- plane grounded!! (Ken)
3. 01:43 PM - Re: Re: A200/Flightcom 403 radio not transmitting- plane grounded!! (Henry Hallam)
4. 03:51 PM - Re: AeroElectric-List Digest: 29 Msgs - 11/05/12 (Allan Chong)
5. 05:17 PM - Beautiful Jade Pendants Online! (dshfjhj)
6. 06:22 PM - for Bob (RGent1224@aol.com)
7. 09:40 PM - Re: for Bob (Robert L. Nuckolls, III)
8. 09:52 PM - Re: for Bob (dstevenco@comcast.net)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: A200/Flightcom 403 radio not transmitting- plane |
grounded!!
Well...... Radio seems fine. Only thing that was out of whack was the sidetone.
Apparently it was set really high. Not sure if that has any effect or not.
Getting radio back on Friday.... So, we will see. Guess its time to move on to
other possibilities..... :-/
Chad
--------
C-GYXQ. 912ULS. 601XL-B
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=387173#387173
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: A200/Flightcom 403 radio not transmitting- |
plane grounded!!
Yes it might. Factory settings of sidetone and mic gain were too high
for my headset causing distortion. Believe I also had to increase
squelch. Has worked well after that for several years now.
Ken
On 07/11/2012 3:18 PM, SIDESLIP wrote:
> --> AeroElectric-List message posted by:
> "SIDESLIP"<Chad2007@rogers.com>
>
> Well...... Radio seems fine. Only thing that was out of whack was the
> sidetone. Apparently it was set really high. Not sure if that has any
> effect or not.
>
> Getting radio back on Friday.... So, we will see. Guess its time to
> move on to other possibilities..... :-/
>
> Chad
>
> -------- C-GYXQ. 912ULS. 601XL-B
>
>
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: A200/Flightcom 403 radio not transmitting- |
plane grounded!!
I had some squealing issues with my DIY intercom and Garmin 480 that were
resolved by turning the sidetone on the 480 all the way to 0. (The intercom
provides sidetone). Not sure whether that's relevant to your situation.
Henry
On Wed, Nov 7, 2012 at 12:42 PM, Ken <klehman@albedo.net> wrote:
>
> Yes it might. Factory settings of sidetone and mic gain were too high
> for my headset causing distortion. Believe I also had to increase
> squelch. Has worked well after that for several years now.
> Ken
>
>
> On 07/11/2012 3:18 PM, SIDESLIP wrote:
>
>> --> AeroElectric-List message posted by:
>> "SIDESLIP"<Chad2007@rogers.com**>
>>
>> Well...... Radio seems fine. Only thing that was out of whack was the
>> sidetone. Apparently it was set really high. Not sure if that has any
>> effect or not.
>>
>> Getting radio back on Friday.... So, we will see. Guess its time to
>> move on to other possibilities..... :-/
>>
>> Chad
>>
>> -------- C-GYXQ. 912ULS. 601XL-B
>>
>>
>>
>>
>
>
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: AeroElectric-List Digest: 29 Msgs - 11/05/12 |
> Time: 07:02:26 AM PST US
> From: Tim Olson <Tim@MyRV10.com>
> Subject: Re: AeroElectric-List: Re: Soldering Iron Recommendations
>
> Is there a chance that you or someone could offer up what would be a
> good model of station to go with for someone who wants to do
> general electronics/avionics work? I noted you said the STTC-147
> tips. Just browsed eBay and saw there are many models.
> I have 2 weller stations right now, and use the tiny point pencil
> tips quite a bit. I don't really *need* a new station, but hey,
> if they're as good as you say, I could be up for buying one.
> I' probably get new though if possible.
> Tim
>
I've got a PS2E. Works very very well and was maybe $50 on ebay.
I've heard the cords are fragile, but I've never had a problem.
If you've used the standard cheap Weller or worse, you'll wonder what
the heck you were doing before. It certainly wasn't soldering.
Btw, after getting a ride in a RV6 at the factory years ago, the
pilot stopped in one of their front hangar rooms and showed part
of a 4 place plane being riveted. "We think we're going to call this
the RV10"
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Beautiful Jade Pendants Online! |
This developed normal Jade Pendant (http://www.jadejewelrymall.com/jadeite-pendant.html) is put by 18k shiny precious metal or jewelry and developed with a small historical cash necklace, a jadeite tablet and a precious metal variety on the top. Both of top and base of normal jade pendant is developed with a small jadeite tablet. The exterior of normal jade pendant is strong and challenging. Green Jade (http://www.jadejewelrymall.com) The gorgeous dark red with dark-colored normal are involved and allocated all over this necklace. It is also developed with ice shiny and lighting normal of jadeite necklace and pellets and make it look more dynamic.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=387195#387195
Message 6
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
I sent you an E-Mail thru your web site and I believe it to be rejected for
improper email address format that I put in correctly.
Here is the message that I sent you
Thanks
Dick
I have the following crimper and would like to get the instruction sheet
for it if possible
Manufacturer: Clark CABLE
Part Number: MS25037-1A
FSN: 5120-00-596-9313
I've had it for a long time and played with it but am now getting ready to
wire my homebuilt airplane and would like to know that I'm using it
properly.
Thanks
Dick
E-Mail _rgent1224@aol.com_ (mailto:rgent1224@aol.com)
Message 7
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
At 08:21 PM 11/7/2012, you wrote:
>I sent you an E-Mail thru your web site and I believe it to be
>rejected for improper email address format that I put in correctly.
>Here is the message that I sent you
>Thanks
>Dick
>
>I have the following crimper and would like to get the instruction
>sheet for it if possible
>Manufacturer: Clark CABLE
>Part Number: MS25037-1A
>FSN: 5120-00-596-9313
>I've had it for a long time and played with it but am now getting
>ready to wire my homebuilt airplane and would like to know that I'm
>using it properly.
>Thanks
>Dick
>E-Mail <mailto:rgent1224@aol.com>rgent1224@aol.com
Yeah, I've got a bug I need to fix on that
script. I don't think there's a manual for
that tool. They're pretty generic technology.
Bob . . .
Message 8
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Bob,
The same thing happened to me when I tried to order your book. I am wiring up my
Zenith with your z-16.
Good luck fixing the problem.
Darren
----- Original Message -----
From: "Robert L. Nuckolls, III" <nuckolls.bob@aeroelectric.com>
Sent: Wednesday, November 7, 2012 9:39:29 PM
Subject: Re: AeroElectric-List: for Bob
At 08:21 PM 11/7/2012, you wrote:
I sent you an E-Mail thru your web site and I believe it to be rejected for improper
email address format that I put in correctly.
Here is the message that I sent you
Thanks
Dick
I have the following crimper and would like to get the instruction sheet for it
if possible
Manufacturer: Clark CABLE
Part Number: MS25037-1A
FSN: 5120-00-596-9313
I've had it for a long time and played with it but am now getting ready to wire
my homebuilt airplane and would like to know that I'm using it properly.
Thanks
Dick
E-Mail rgent1224@aol.com
Yeah, I've got a bug I need to fix on that
script. I don't think there's a manual for
that tool. They're pretty generic technology.
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|