---------------------------------------------------------- AeroElectric-List Digest Archive --- Total Messages Posted Wed 07/16/14: 3 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 02:13 PM - Z-13/8 and SD-8 (MikeDunlop) 2. 05:06 PM - Re: Dual master solenoids (Eric M. Jones) 3. 09:49 PM - P Lead Wires Adjacent to Headset Jack Wires (stearman456) ________________________________ Message 1 _____________________________________ Time: 02:13:47 PM PST US Subject: AeroElectric-List: Z-13/8 and SD-8 From: "MikeDunlop" A little clarification required on the Z-13/8 schematic. I'm building this into a Long-Ez and have the SD-8 with all the bits from B&C. The Z-13/8 schematic shows something that is marked as W10 that appears to be between the Dynamo and the Regulator! This does NOT appear on the schematic from B&C. Any info on this would be appreciated. Regards MikeD (UK) Read this topic online here: http://forums.matronics.com/viewtopic.php?p=426799#426799 ________________________________ Message 2 _____________________________________ Time: 05:06:21 PM PST US Subject: AeroElectric-List: Re: Dual master solenoids From: "Eric M. Jones" I say "ditto" to everything Stein said. I firmly believe that one well-built system is better than a poor one with a backup... or a couple backups. My philosophy even extents to Ballistic Parachute Systems (which have been around for almost a century). My analysis says that a set of well-built and tested wings on a GA aircraft with no backup is a better way to go. -------- Eric M. Jones www.PerihelionDesign.com 113 Brentwood Drive Southbridge, MA 01550 (508) 764-2072 emjones(at)charter.net Read this topic online here: http://forums.matronics.com/viewtopic.php?p=426803#426803 ________________________________ Message 3 _____________________________________ Time: 09:49:01 PM PST US Subject: AeroElectric-List: P Lead Wires Adjacent to Headset Jack Wires From: "stearman456" In the interests of killing two birds with one stone, could I run my headset and mic jack wires in the same 3/8" dia aluminum conduit as my mags' P lead wires without screwing up my audio signals? Inasmuch as the P lead wires need to be shielded I'm thinking this is probably a really bad idea and would probably cripple my audio but as it would make such a slick installation in my case I thought I'd ask. (Plain, old, Bendix mags, Garmin SL40 com). Thanks. Dan Read this topic online here: http://forums.matronics.com/viewtopic.php?p=426817#426817 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message aeroelectric-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/AeroElectric-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/aeroelectric-list Browse Digests http://www.matronics.com/digest/aeroelectric-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.