---------------------------------------------------------- AeroElectric-List Digest Archive --- Total Messages Posted Sun 03/19/17: 2 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 12:44 PM - Re: Garmin magnetometer installation. (Robert L. Nuckolls, III) 2. 02:41 PM - Re: Garmin magnetometer installation. (Stein Bruch) ________________________________ Message 1 _____________________________________ Time: 12:44:10 PM PST US From: "Robert L. Nuckolls, III" Subject: Re: AeroElectric-List: Garmin magnetometer installation. At 10:12 AM 3/17/2017, you wrote: > Thank you Stein for the reference to the wiring diagram, I > hadn't seen it, had only looked in the magnetometer section. I > figured it would require shielded wiring. The twisted pairs I was > referring to are for the other wiring in the same wing, a Whelen > LED position/strobe unit and a Facet fuel transfer pump. Whelen > wants 20 ga wire for their unit and I need 16 gauge wire for the > pump. I would buy twisted pair wire for these but I only see 22 ga > twisted pair wire on your website. Maybe the best option is to use > shielded wire for both. > Bob, thanks for your offer on shielded wire. I would need 50' > total for the two runs to the magnetometer. I've sent you a paypal invoice for shipping Bob . . . ________________________________ Message 2 _____________________________________ Time: 02:41:59 PM PST US From: "Stein Bruch" Subject: RE: AeroElectric-List: Garmin magnetometer installation. For the facet pump I wouldn't worry too much if it were me (it's only a periodic load anyway). For the strobes, we usually see (and stock) 3 conductor x AWG20 or AWG18 depending on what the mfgr spec's. Cheers, Stein From: owner-aeroelectric-list-server@matronics.com [mailto:owner-aeroelectric-list-server@matronics.com] On Behalf Of Robert L. Nuckolls, III Sent: Sunday, March 19, 2017 2:41 PM Subject: Re: AeroElectric-List: Garmin magnetometer installation. At 10:12 AM 3/17/2017, you wrote: Thank you Stein for the reference to the wiring diagram, I hadn't seen it, had only looked in the magnetometer section. I figured it would require shielded wiring. The twisted pairs I was referring to are for the other wiring in the same wing, a Whelen LED position/strobe unit and a Facet fuel transfer pump. Whelen wants 20 ga wire for their unit and I need 16 gauge wire for the pump. I would buy twisted pair wire for these but I only see 22 ga twisted pair wire on your website. Maybe the best option is to use shielded wire for both. Bob, thanks for your offer on shielded wire. I would need 50' total for the two runs to the magnetometer. I've sent you a paypal invoice for shipping Bob . . . ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message aeroelectric-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/AeroElectric-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/aeroelectric-list Browse Digests http://www.matronics.com/digest/aeroelectric-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.