Today's Message Index:
----------------------
1. 07:43 AM - unable to receive auyomatic list e-mails (Chuck and LaVerne Stroh)
2. 01:22 PM - Re: Re: EFIS/EMS Brownout/Reboot: =?iso-8859-1?Q?=9CVoltage?= =?iso-8859-1?Q?_Slump_Eliminator=9D? (Robert L. Nuckolls, III)
3. 05:06 PM - Clever Wiring for Lamp Dimmer (Art Zemon)
4. 05:25 PM - Re: Clever Wiring for Lamp Dimmer (Daniel Hooper)
5. 05:48 PM - Re: unable to receive auyomatic list e-mails (Robert L. Nuckolls, III)
6. 06:12 PM - Re: unable to receive auyomatic list e-mails (Art Zemon)
7. 07:08 PM - Re: Clever Wiring for Lamp Dimmer (Eric Page)
8. 07:14 PM - Re: EFIS/EMS Brownout/Reboot: =?ISO-8859-1?Q?=9CVoltage?= Slump =?ISO-8859-1?Q?Eliminator=9D? (Eric Page)
9. 08:08 PM - Re: unable to receive auyomatic list e-mails (Cliff Princehorn)
10. 09:02 PM - Re: Clever Wiring for Lamp Dimmer (Charlie England)
11. 09:53 PM - Re: Clever Wiring for Lamp Dimmer (Bob Verwey)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | unable to receive auyomatic list e-mails |
Hello Matt
I have been a member of the list for a number of years.
About 6 weeks ago I stopped receiving e-mail updated from the list.
I have made no changes to my account.
Please help. CLSTROH@YAHOO.COM
Regards
Chuck
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: EFIS/EMS Brownout/Reboot: =?iso-8859-1?Q?=9CVoltage?= |
=?iso-8859-1?Q?_Slump_Eliminator=9D?
>
>
>In this case, it looks like a lead-acid battery or one of the TCW
>Li-Fe-PO packs...
>
>http://www.tcwtech.com/ibbs_integrated_backup_battery_system_3ah_6ah.html
>
>...might be your best bet.
Are ALL the power inputs subject to brownout reboot
syndrome? A nav and comm receivers are very quick
to come on line and 'heaters' certainly don't
need to be supported.
Bob . . .
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Clever Wiring for Lamp Dimmer |
Folks,
I have ten backlit switches in the panel of my plane. I need to wire all of
them to the same dimmer, see the diagram on page 4 of the attached
AeroRockers Circuit Diagrams, specifically the red line to the PULSE-WIDTH
DIMMER box. The switches have Faston tabs. Is there some clever way to wire
this? Do I just build something with a Faston terminal at one end for the
dimmer and then 10 wires coming out of it, all tied up into a bundle, each
with another Faston terminal?
-- Art Z.
--
https://CheerfulCurmudgeon.com/
*"If I am not for myself, who is for me? And if I am only for myself, what
am I? And if not now, when?" Hillel*
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Clever Wiring for Lamp Dimmer |
Maybe you can wire a running string of fast-ons with two wires coming out of
each fast-on? It reduces reliability to wire in series like that, but switc
h illumination is relatively(?) non-critical..
Daniel
> On Dec 7, 2017, at 7:06 PM, Art Zemon <art@zemon.name> wrote:
>
> Folks,
>
> I have ten backlit switches in the panel of my plane. I need to wire all o
f them to the same dimmer, see the diagram on page 4 of the attached AeroRoc
kers Circuit Diagrams, specifically the red line to the PULSE-WIDTH DIMMER b
ox. The switches have Faston tabs. Is there some clever way to wire this? Do
I just build something with a Faston terminal at one end for the dimmer and
then 10 wires coming out of it, all tied up into a bundle, each with anothe
r Faston terminal?
>
> -- Art Z.
>
> --
> https://CheerfulCurmudgeon.com/
>
> "If I am not for myself, who is for me? And if I am only for myself, what a
m I? And if not now, when?" Hillel
> <AeroRocker Circuit Diagrams.pdf>
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: unable to receive auyomatic list e-mails |
At 09:35 AM 12/7/2017, you wrote:
>Hello Matt
>I have been a member of the list for a number of years.
>About 6 weeks ago I stopped receiving e-mail updated from the list.
>I have made no changes to my account.
>Please help.=C2 <mailto:CLSTROH@YAHOO.COM>CLSTROH@YAHOO.COM
>Regards
>Chuck
Not sure what the 'notice' was about. I checked
your subscription status on matronics and found
this . . .
Emacs!
If this differs from what you have subscribed
to, then you can go to http://matronics.com/subscribe
and fix it.
Bob . . .
Message 6
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: unable to receive auyomatic list e-mails |
Bob,
Something unsubscribed me. I had to resubscribe tonight so that I could
post a message.
-- Art Z.
Sent from my phone. Please excuse brevity and bizarre typos.
On Dec 7, 2017 8:07 PM, "Robert L. Nuckolls, III" <
nuckolls.bob@aeroelectric.com> wrote:
> At 09:35 AM 12/7/2017, you wrote:
>
> Hello Matt
> I have been a member of the list for a number of years.
> About 6 weeks ago I stopped receiving e-mail updated from the list.
> I have made no changes to my account.
> Please help.=C3=82 CLSTROH@YAHOO.COM
> Regards
> Chuck
>
>
> Not sure what the 'notice' was about. I checked
> your subscription status on matronics and found
> this . . .
>
> [image: Emacs!]
>
> If this differs from what you have subscribed
> to, then you can go to http://matronics.com/subscribe
> and fix it.
>
>
> Bob . . .
>
Message 7
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Clever Wiring for Lamp Dimmer |
How about using Bob's concept for power and ground buses based on a D-Sub connector,
but use it to tie your switch illumination lines together? His example
uses a DB-25 connector, but you could substitute a DB-15 since you need fewer
pins.
http://aeroelectric.com/Pictures/Grounding/Minibus1.jpg
Get both male and female connectors. Bridge all of the pins together on one of
them, then solder your wires to the solder cups on the other one. Mate the connectors
and you've got a switch illumination bus.
Male: https://www.digikey.com/short/qqq39z
Female: https://www.digikey.com/short/qqq39m
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=476236#476236
Message 8
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: EFIS/EMS Brownout/Reboot: =?ISO-8859-1?Q?=9CVoltage?= |
Slump =?ISO-8859-1?Q?Eliminator=9D?
nuckolls.bob(at)aeroelect wrote:
> Are ALL the power inputs subject to brownout reboot syndrome? Nav and comm receivers
are very quick to come on line and 'heaters' certainly don't need to be
supported.
Judging by the installation manual, the heater is powered by the "Main" input,
so it's probably not possible to segregate it. I don't know about the Nav and
Comm inputs; I have no experience with the GNS480.
Eric
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=476237#476237
Message 9
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | unable to receive auyomatic list e-mails |
Matt,
This came to my computer, i think by error.
Cheers
Cliff Princehorn
502 / 17 Edgar Street
Belmont NSW 2280
Australia
Ph 02 4947 9290
Mob 0414 527 509
From: owner-aeroelectric-list-server@matronics.com
[mailto:owner-aeroelectric-list-server@matronics.com] On Behalf Of
Robert L.
Nuckolls, III
Sent: Friday, 8 December 2017 12:48 PM
Subject: Re: AeroElectric-List: unable to receive auyomatic list e-mails
At 09:35 AM 12/7/2017, you wrote:
Hello Matt
I have been a member of the list for a number of years.
About 6 weeks ago I stopped receiving e-mail updated from the list.
I have made no changes to my account.
Please help.=C2 CLSTROH@YAHOO.COM
Regards
Chuck
Not sure what the 'notice' was about. I checked
your subscription status on matronics and found
this . . .
Emacs!
If this differs from what you have subscribed
to, then you can go to http://matronics.com/subscribe
and fix it.
Bob . . .
Message 10
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Clever Wiring for Lamp Dimmer |
On 12/7/2017 7:06 PM, Art Zemon wrote:
> Folks,
>
> I have ten backlit switches in the panel of my plane. I need to wire
> all of them to the same dimmer, see the diagram on page 4 of the
> attached AeroRockers Circuit Diagrams, specifically the red line to
> the PULSE-WIDTH DIMMER box. The switches have Faston tabs. Is there
> some clever way to wire this? Do I just build something with a Faston
> terminal at one end for the dimmer and then 10 wires coming out of it,
> all tied up into a bundle, each with another Faston terminal?
>
> -- Art Z.
>
> --
> https://CheerfulCurmudgeon.com/
>
> /"If I am not for myself, who is for me? And if I am only for myself,
> what am I? And if not now, when?" Hillel/
That would work fine, or for wiring convenience, you could do multiple
joints using the same technique. Say, 3 in the 1st faston, and 3 or 4
into a butt splice on the end of each of the 1st 3.
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
Message 11
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Clever Wiring for Lamp Dimmer |
Question from a neophyte....does the dimmer not create some kind of
electrical "noise"?
Best...
Bob Verwey
082 331 2727
On 8 December 2017 at 07:06, Charlie England <ceengland7@gmail.com> wrote:
> On 12/7/2017 7:06 PM, Art Zemon wrote:
>
> Folks,
>
> I have ten backlit switches in the panel of my plane. I need to wire all
> of them to the same dimmer, see the diagram on page 4 of the attached
> AeroRockers Circuit Diagrams, specifically the red line to the PULSE-WIDTH
> DIMMER box. The switches have Faston tabs. Is there some clever way to wire
> this? Do I just build something with a Faston terminal at one end for the
> dimmer and then 10 wires coming out of it, all tied up into a bundle, each
> with another Faston terminal?
>
> -- Art Z.
>
> --
> https://CheerfulCurmudgeon.com/
>
> *"If I am not for myself, who is for me? And if I am only for myself, what
> am I? And if not now, when?" Hillel*
>
> That would work fine, or for wiring convenience, you could do multiple
> joints using the same technique. Say, 3 in the 1st faston, and 3 or 4 into
> a butt splice on the end of each of the 1st 3.
>
>
> <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient&utm_term=icon> Virus-free.
> www.avast.com
> <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient&utm_term=link>
> <#m_1398500146610424097_DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|