Today's Message Index:
----------------------
1. 08:19 AM - Re: Z-11 superseded? It's not in the PDF folder (Robert L. Nuckolls, III)
2. 09:48 AM - Mitchell Voltmeter (Bean)
3. 09:54 AM - Re: Z-11 superseded? It's not in the PDF folder (Charlie England)
4. 10:47 AM - Re: Mitchell Voltmeter (Charlie England)
5. 06:56 PM - EXTERNAL PWR with MASTER/BATT SWITCH? (supik)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Z-11 superseded? It's not in the PDF folder |
At 07:13 PM 5/15/2020, you wrote:
><john_s_bright@yahoo.com>
>
>Hi Bob,
>
>Question... has Z-11 been superseded? It's not in the PDF folder but
>it is in the ACAD Dwg folder at http://www.aeroelectric.com/PPS/
Not quite yet. I don't remember taking it down.
It's back up. Z101 will eventually replace a number
of the legacy z-figures.
Bob . . .
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Mitchell Voltmeter |
I am installing a Mitchell voltmeter in my RV. It has terminals that look like
faston but they are bigger.
The largest faston, series 250, will not fit. It may be that a connector is intended
rather that terminals.
Anyway what connector/terminal is appropriate?
thanks and cheers Jim
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Z-11 superseded? It's not in the PDF folder |
On Sat, May 16, 2020 at 10:24 AM Robert L. Nuckolls, III <
nuckolls.bob@aeroelectric.com> wrote:
> At 07:13 PM 5/15/2020, you wrote:
>
> john_s_bright@yahoo.com>
>
> Hi Bob,
>
> Question... has Z-11 been superseded? It's not in the PDF folder but it is
> in the ACAD Dwg folder at http://www.aeroelectric.com/PPS/
>
>
> Not quite yet. I don't remember taking it down.
> It's back up. Z101 will eventually replace a number
> of the legacy z-figures.
>
>
> Bob . . .
>
I might have mentioned this in the past (I know that I've thought it...)
My vote is to never *replace* a drawing. Revise, supersede, etc; sure. But
if a numbered drawing disappears, someone who followed it in the past (or
bought an a/c that used it) may need to find it again at some point down
the road. A good example is the OV circuit for IR alternators. Some of us
made an informed choice to use IR alts, but at some point, the doc
detailing the circuit disappeared. Not an issue for a wire-head, but might
cause real consternation for someone down the road who isn't
electronic-savvy.
Why not just water-mark it 'superseded' with notes including the reason &
where to go to find the new, preferred concept?
Charlie
<https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail&utm_term=icon>
Virus-free.
www.avast.com
<https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail&utm_term=link>
<#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Mitchell Voltmeter |
On 5/16/2020 11:44 AM, Bean wrote:
>
> I am installing a Mitchell voltmeter in my RV. It has terminals that
> look like faston but they are bigger.
>
> The largest faston, series 250, will not fit. It may be that a
> connector is intended rather that terminals.
>
> Anyway what connector/terminal is appropriate?
>
> thanks and cheers Jim
>
Maybe like this?
https://www.ferrulesdirect.com/collections/quick-disconnects/products/fdnyd5-375
I've bought several packs of various sizes of quick disconnects, butt
splices, ring terminals, etc from them, and I've been pleased with them.
The ones I linked are .375" width.
The website is kinda funky to navigate, but they likely have whatever
you might need. Not claiming that they are as good as the 'gold
standard', but the certainly seem good enough. I used my B&C-supplied
crimper on them.
Charlie
--
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | EXTERNAL PWR with MASTER/BATT SWITCH? |
What's the reason, most of the certified aiplanes do not allow connecting the External
Power Src without turning the MASTER / BATTERY contactor ON?
--------
Igor
RV10 in progress
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=496418#496418
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|