Today's Message Index:
----------------------
1. 06:44 AM - Re: 3 stage switching for lights (Chuck)
2. 07:07 AM - Re: 3 stage switching for lights (Werner Schneider)
3. 09:40 AM - Re: Filling All the Holes in a DB Connector (John M Tipton)
4. 12:56 PM - Fw: Activation of account, Matronics Email Lists Forums - "esco" (stuart anderson)
5. 01:14 PM - Re: 3 stage switching for lights (Werner Schneider)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: 3 stage switching for lights |
Hello Mike,
I have found the following information very helpful in designing unusual
toggle switch wiring configurations, which seems to be your case.
Go to Bob's AeroElectric Connection book, Page EX11-2.
Or, use this link on the B&C website: AeroElectric Connection - "Switch
Ratings, What's It All Mean?":
https://bandc.com/wp-content/uploads/2018/05/aec_switch_ratings.pdf
There are the pole diagrams for the different toggle switch configurations
available through B&C.
One of these might work for you.
Good Luck,
Chuck
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: 3 stage switching for lights |
Thanks Chuck,
I did that beforehand, however it needs some bridging of some contacts
to achieve what I need, Bob's link did provide that information.
Cheers Werner
On 05.12.2023 15:43, Chuck wrote:
>
> Hello Mike,
>
> I have found the following information very helpful in designing
> unusual toggle switch wiring configurations, which seems to be your case
.
>
> Go to Bob's AeroElectric Connection book, Page EX11-2.
>
> Or, use this link on the B&C website:=C2- AeroElectric Connection -
> "Switch Ratings, What's It All Mean?":
>
> https://bandc.com/wp-content/uploads/2018/05/aec_switch_ratings.pdf
>
> There are the pole diagrams for the different toggle switch
> configurations available through B&C.
>
> One of these might work for you.
>
> Good Luck,
>
> Chuck
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Filling All the Holes in a DB Connector |
With the price of those pins: forget it ~
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=512759#512759
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Fwd: Activation of account, Matronics Email Lists Forums |
- "esco"
Team: request re-activation of my account- I'm working on the architecture
for my RV-14A project.
Thanks!
---------- Forwarded message ---------
From: stuart anderson <stuart.td.anderson@gmail.com>
Subject: Re: Activation of account, Matronics Email Lists Forums - "esco"
Mr. Dralle: following up on this.
Ron Willis
---------- Forwarded message ---------
From: stuart anderson <stuart.td.anderson@gmail.com>
Subject: Re: Activation of account, Matronics Email Lists Forums - "esco"
Following up on AeroElectric List access request.
Ron Willis
--------------------
On Sat, Jan 14, 2023 at 7:19 AM stuart anderson <
stuart.td.anderson@gmail.com> wrote:
> Mr. Dralle: Is my account active?
> I've not received a second email to indicate it was activated, and I've
> tried to log in without success.
>
> Thank you.
>
>
> ---------- Forwarded message ---------
> From: <dralle@matronics.com>
> Date: Wed, Jan 11, 2023 at 9:00 PM
> Subject: Welcome to Matronics Email Lists Forums
> To: <stuart.td.anderson@gmail.com>
>
>
> Welcome to the Matronics Email Lists
>
> Please keep this email for your records. Your account information is as
> follows:
>
> ----------------------------
> Username: esco
> Password: STuart@#2002
> ----------------------------
>
> Your account is currently inactive, the administrator of the board will
> need to activate it before you can log in. You will receive another email
> when this has occured.
>
> Please do not forget your password as it has been encrypted in our
> database and we cannot retrieve it for you. However, should you forget yo
ur
> password you can request a new one which will be activated in the same wa
y
> as this account.
>
> Thank you for registering.
>
> --
> Matt Dralle
> Matronics Email List/Forum Administrator
>
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: 3 stage switching for lights |
Thanks M,
that is it, sorry got that mail in the spam folder lost before seen now.
Cheers Werner
On 04.12.2023 16:29, M Wilson wrote:
> It looks like you need a DP3T switch.=C2- Do a search for them.=C2-
It seems
> that it is a 4PDT switch with a jumper. You can search for those also.
> The selection seems to be limited.=C2- There are several with PC pins
and
> some expensive ones with screw terminals.
> I've never used one.=C2- They have 12 terminals on the back of the
> switch, but you don't need any diodes.
> See the last page on the attached; it shows the jumper wiring.
>
>
> On Sunday, December 3, 2023 at 03:58:08 PM CST, Werner Schneider
> <glastar@gmx.net> wrote:
>
>
> Thanks M,
>
> the circuit shown for the dimmer is not exactly the product used, the
> Perhelion dimer has an integrated on-off switch. And the LED's are
> strips with resistors for 12 V.
>
> The problem I see is, in the position where the rear led strip is on
> full voltage via pin 2, the front is as well on the dimmer, that is
> not what I want. so that position is not independent. I would like to
> have 3 independent switch position.
>
> Cheers Werner
>
> On 02.12.2023 19:50, M Wilson wrote:
> That looks like it should work.
> I'd pull the feed for switch input pin2 from before the dimmer and use
> one fuse.
> I assume there are series resistors as part of the cabin LEDs to limit
> current?=C2- If, not they are needed.
>
> The LM317 dimmer circuit will not go to a completely off state.
>
>
> On Saturday, December 2, 2023 at 11:37:32 AM CST, Werner Schneider
> <glastar@gmx.net> <mailto:glastar@gmx.net> wrote:
>
>
> Thanks Bob,
>
> The dimmer has the off functionality, so 3 position would work but
> need to have 2 feeders, diodes would be against crossfeed here my
> architecture, but the switch will not work this way
>
>
> On 02.12.2023 17:32, Bob Kuc wrote:
> I would think that you need a 4 position switch since off position
> would be needed.=C2- I would just=C2- go with 2 switches, but if you
want
> only one then look at a 4 position rotary switch.
>
> 1 off
> 2 front
> 3 back
> 4 both
>
> On Sat, Dec 2, 2023, 10:37=AFAM Christopher Cee Stone
> <rv8iator@gmail.com <mailto:rv8iator@gmail.com>> wrote:
>
> image.png
> Take at the functions. It appears to me this is what you want.
>
> Also
> https://www.ebay.com/itm/293559818578?chn=ps&norover=1&mkevt=1
&mkrid=711-117182-37290-0&mkcid=2&mkscid=101&itemid=293559818578&t
argetid=1490630670660&device=c&mktype=pla&googleloc=9032917&poi=
&campaignid=19851828444&mkgroupid=145880009014&rlsatarget=pla-149063
0670660&abcId=9307249&merchantid=114784040&gclid=Cj0KCQiAyKurBhD5ARI
sALamXaHdlww9Fe9Yu1ydQyAe6anUXRiGz4KA3n6oG3-clEaFpkyQR-CLpzUaAsIYEALw_wcB
> <https://www.ebay.com/itm/293559818578?chn=ps&norover=1&mkevt=
1&mkrid=711-117182-37290-0&mkcid=2&mkscid=101&itemid=293559818578&
targetid=1490630670660&device=c&mktype=pla&googleloc=9032917&poi
=&campaignid=19851828444&mkgroupid=145880009014&rlsatarget=pla-149
0630670660&abcId=9307249&merchantid=114784040&gclid=Cj0KCQiAyKurBhD5
ARIsALamXaHdlww9Fe9Yu1ydQyAe6anUXRiGz4KA3n6oG3-clEaFpkyQR-CLpzUaAsIYEALw_w
cB>
>
> ...chris
>
> On Sat, Dec 2, 2023 at 7:26=AFAM Werner Schneider <glastar@gmx
.net
> <mailto:glastar@gmx.net>> wrote:
>
> Thanks Christopher,
>
> but they do not work as they have not 3 independent position
>
>
> it's always a set of 2 closed so eg. if you feed from 5 and 2
> you could do 5-4 up, 5-6 middle but then down you would have
> 2-3 but 5-6 would be closed as well :(
>
> On 02.12.2023 16:00, Christopher Cee Stone wrote:
>> Many from on-line vendors:
>> https://www.amazon.com/GAMA-Electronics-Toggle-Switch-Position/
dp/B001PNMC16
>> <https://www.amazon.com/GAMA-Electronics-Toggle-Switch-Position
/dp/B001PNMC16>
>>
>> https://www.steinair.com/product/toggle-switch-3-position-dpdt/
>> <https://www.steinair.com/product/toggle-switch-3-position-dpdt
/>
>>
>> https://bandc.com/product/toggle-switch-double-pole/?attribute_
configuration=-10+ON-ON-ON
>> <https://bandc.com/product/toggle-switch-double-pole/?attribute
_configuration=-10+ON-ON-ON>
>>
>>
>>
>> On Fri, Dec 1, 2023 at 3:12=AFPM werner schneider
>> <glastar@gmx.net <mailto:glastar@gmx.net>> wrote:
>>
>> schneider" <glastar@gmx.net <mailto:glastar@gmx.net>>
>>
>> Hi Folks,
>>
>> I wonder if I could save on a 4th dimmer ;) Here what I
>> want to achieve:
>>
>> Cabin lights (LED) 2 section, front and rear:
>>
>> -position 1, front lights on dimmer, rear lights off
>> -position 2, front and rear lights on dimmer
>> -position 3, front lights off, rear lights on 13.8V
>>
>> I did craft a scheme, but I'm not able to find a switch
>> which offer that 3 stage functionality or maybe I'm just
>> not good enough in wiring it for that functionality.
>>
>> Thanks for your help (due to space constrains the switch
>> would need to use screw terminals in addition)
>>
>> Werner
>>
>>
>>
>>
>> Read this topic online here:
>>
>> http://forums.matronics.com/viewtopic.php?p=512721#512721
>> <http://forums.matronics.com/viewtopic.php?p=512721#51272
1>
>>
>>
>>
>>
>>
>>
>> ==========
>> -
>> Electric-List" rel="noreferrer"
>> target="_blank">http://www.matronics.com/Navigator?AeroEl
ectric-List
>> <http://www.matronics.com/Navigator?AeroElectric-List>
>> ==========
>> FORUMS -
>> eferrer" target="_blank">http://forums.matronics.com
>> <http://forums.matronics.com>
>> ==========
>> WIKI -
>> errer" target="_blank">http://wiki.matronics.com
>> <http://wiki.matronics.com>
>> ==========
>> b Site -
>> =C2- =C2- =C2- =C2- =C2- -Matt Dralle, List Admin
.
>> ="noreferrer"
>> target="_blank">https://matronics.com/contribution
>> <https://matronics.com/contribution>
>> ==========
>>
>>
>>
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|