Allegro-List Digest Archive

Sat 08/05/06


Total Messages Posted: 2



Today's Message Index:
----------------------
 
     1. 03:03 AM - Re: Cabin Throttle Lever/ Bowen Cable Connection (Thom Riddle)
     2. 04:07 AM - Re: Cabin Throttle Lever/ Bowen Cable Connection (Dave Grosvenor - DreamWings)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 03:03:42 AM PST US
    From: Thom Riddle <jtriddle@adelphia.net>
    Subject: Re: Cabin Throttle Lever/ Bowen Cable Connection
    --> Allegro-List message posted by: Thom Riddle <jtriddle@adelphia.net> Hugh, I'm going to fly our Allegro for my BFR today. While at the hangar I'll try to get a couple close-up photos of this are and post them this evening. Thom in Buffalo


    Message 2


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 04:07:00 AM PST US
    From: "Dave Grosvenor - DreamWings" <dave@dreamwings.co.za>
    Subject: Re: Cabin Throttle Lever/ Bowen Cable Connection
    --> Allegro-List message posted by: "Dave Grosvenor - DreamWings" <dave@dreamwings.co.za> Hi Hugh, I don't have a picture but if I remember correctly the throttle cable has a stop swaged onto the one end. The other end of the cable gets pushed through the hole, fed through the cable outer and onto the throttle lever on the carb. The throttle lever on the carb has a spring pulling it to the open position, and this maintains tension on the cable. So when you open the throttle, the cable gets pulled forward by the spring on the throttle arm on the carb. When you close the throttle, the swaged stop can't go through the clevis and the cable is pulled back. Regards Dave ----- Original Message ----- > Time: 10:36:57 AM PST US > From: "Hugh McKay III" <hgmckay@bellsouth.net> > Subject: Allegro-List: Cabin Throttle Lever/ Bowen Cable Connection > > As many of you know by now I am trying to finish my Allegro 2000 Kit. > Among > many small details that I have been unable to get help from my Distributor > (i.e. its a kit, you figure it out), one is the following question > concerning how to connect the throttle cable to the throttle lever clevis. > > The cabin throttle lever has a metal clevis that is connected to the lever > and swivels as the lever is moved. This clevis has a small hole in it for > the cable to pass through. I have nothing to connect the cable to the > clevis. Could some one look at their connection and explain how this is > done. A close-up photograph would be very helpful. If your plane was > purchased ready-to-fly you probably did not have to make this connection. > I > simply dont have any parts for this and I need some direction. > > This may not be my last request for help in these small matters. All of > your > past advice and help is deeply appreciated. If I didnt have you guys (The > Matronics Allegro-List) I would be in deep yogurt. Many thanks! > > Hugh McKay > In the deep south where it is Hot! > >




    Other Matronics Email List Services

  • Post A New Message
  •   allegro-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/Allegro-List.htm
  • Full Archive Search Engine
  •   http://www.matronics.com/search
  • 7-Day List Browse
  •   http://www.matronics.com/browse/allegro-list
  • Browse Allegro-List Digests
  •   http://www.matronics.com/digest/allegro-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contributions

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --