Avionics-List Digest Archive

Wed 08/18/04


Total Messages Posted: 1



Today's Message Index:
----------------------
 
     1. 10:10 PM - Re: KA-134 issues (James Redmon)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 10:10:50 PM PST US
    From: "James Redmon" <james@berkut13.com>
    Subject: Re: KA-134 issues
    --> Avionics-List message posted by: "James Redmon" <james@berkut13.com> I have a major correction to make on my post. It is NOT the King audio panel, it is the Microair 760 radio - at least caused by it. Several folks were on to something about the second com. I thought for sure I had tested the problem with the radio off...but I guess I had not. I disconnected com2 and the problem went away. I re-connected it (with the power off) and the problem was still gone. I turned on Com2....poof, I had com 2 audio, but reduced aux audio. Com1 was unaffected by all modes, with or without aux audio. The issues is isolated with com2's audio. Any ideas how I can test this out and equalize the audio? I seem to remember folks having problems with the Microair radio mixing with other audio sources. Thanks for the help! James Redmon Berkut #013 N97TX http://www.berkut13.com > -------- Original Message -------- > Subject: Avionics-List: KA-134 issues > Date: Tue, 17 Aug 2004 11:02:51 -0500 > From: James Redmon <james@berkut13.com> > Reply-To: avionics-list@matronics.com > To: <avionics-list@matronics.com> > > > --> Avionics-List message posted by: "James Redmon" <james@berkut13.com> > > Hi all, > > I've found a small anomaly in my audio system - specifically the KA-135 > audio panel...I think. I have two com radios, the KA-135 has the two > mic/radio select buttons and several inputs for aux audio (NAV1, NAV2, > Marker, DME, etc.) - standard stuff, right. > > I have the audio from the engine computer (audio alerts) piped into the > KA-135 on one of the 5 aux audio lines. With com1 mic switch pushed, all is > fine...everything loud and clear. Problem: when com2 switch is activated, I > can hear com2 audio just fine but ALL other audio inputs seem to have been > muted considerably. I can still hear them but they ALL are significantly > lower in volume. This also happens to all aux audio when the "both" button > is pressed as well. The result - when I'm monitoring com2, I can barely > hear the audio warnings....not good! > > I have checked side tone adjustments on the both coms..no effect. The only > volume adjustment that the KA unit has is for the external speaker...it is > unaffected by the mic select button positions. > > You can get a look at my panel here: http://www.berkut13.com/berkut22.htm > > Can any of you KA-135 users/fixers out there verify that this is normal? > Is there any way to adjust or change this operation mode? There is noting > the manual that describes this behavior.




    Other Matronics Email List Services

  • Post A New Message
  •   avionics-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/Avionics-List.htm
  • Full Archive Search Engine
  •   http://www.matronics.com/search
  • 7-Day List Browse
  •   http://www.matronics.com/browse/avionics-list
  • Browse Avionics-List Digests
  •   http://www.matronics.com/digest/avionics-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contributions

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --