---------------------------------------------------------- Avionics-List Digest Archive --- Total Messages Posted Wed 02/22/06: 5 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 05:28 AM - Pin out (Bob Gibfried) 2. 05:44 AM - Re: Pin out (Bruce Gray) 3. 08:00 AM - Re:MiroAir Radio (aeroads@comcast.net) 4. 08:40 AM - Re: Re:MiroAir Radio (frequent flyer) 5. 11:37 AM - Re: GTX330 TIS with DAC GDC34A/Chelton (Tim Olson) ________________________________ Message 1 _____________________________________ Time: 05:28:15 AM PST US From: "Bob Gibfried" Subject: Avionics-List: Pin out --> Avionics-List message posted by: "Bob Gibfried" Thanks to all who replied to my request for a KMD 150 pin out. First to reply was a gentleman from England. It's an amazing world we live in when a simple request can be met halfway around the world! Now if anyone can point me to a good set of crimpers. Mashing the pins with a needle nose just doesn't work for me. Thanks Bob, Wichita ________________________________ Message 2 _____________________________________ Time: 05:44:23 AM PST US From: "Bruce Gray" Subject: RE: Avionics-List: Pin out --> Avionics-List message posted by: "Bruce Gray" You should go to http://aeroelectric.com/, buy the book and read all the articles on the web site. Then you'll know the right questions to ask. Bruce www.glasair.org -----Original Message----- From: owner-avionics-list-server@matronics.com [mailto:owner-avionics-list-server@matronics.com] On Behalf Of Bob Gibfried Sent: Wednesday, February 22, 2006 8:25 AM Subject: Avionics-List: Pin out --> Avionics-List message posted by: "Bob Gibfried" Thanks to all who replied to my request for a KMD 150 pin out. First to reply was a gentleman from England. It's an amazing world we live in when a simple request can be met halfway around the world! Now if anyone can point me to a good set of crimpers. Mashing the pins with a needle nose just doesn't work for me. Thanks Bob, Wichita ________________________________ Message 3 _____________________________________ Time: 08:00:01 AM PST US From: aeroads@comcast.net Subject: Avionics-List: Re:MiroAir Radio --> Avionics-List message posted by: aeroads@comcast.net Have a MicroAir in an open cockpit biplane: a Stampe the transceiver has great range in both trans and receive with a small ground plane in the rounded turtle deck I use the flexible black rubber coated antenna that was recommended the squelch requires constant attention for both radio and intercom not surprising in the open cockpit but is loud and clear once set my only reservation is reading the frequency settings in some lighting conditions I like to set frequencies before takeoff if I could have installed the unit directly aimed at the pilots eye there would be no grat problem but the panel depth required a side mounting Yup a might fine unit Murray aeroads@comcast.net ________________________________ Message 4 _____________________________________ Time: 08:40:57 AM PST US From: frequent flyer Subject: Re: Avionics-List: Re:MiroAir Radio --> Avionics-List message posted by: frequent flyer I have on in my Cessna 150. Works great but hard to change frequencies in turbulence. Jack --- erodes@comcast.net wrote: > --> Avionics-List message posted by: > aeroads@comcast.net > > Have a MicroAir in an open cockpit biplane: a Stampe ________________________________ Message 5 _____________________________________ Time: 11:37:59 AM PST US From: Tim Olson Subject: Re: Avionics-List: GTX330 TIS with DAC GDC34A/Chelton --> Avionics-List message posted by: Tim Olson Mike, Do you have the GNS480 for a Nav/Com, or the 430/530? I called to ask them for an update today and right now their questioning that maybe the 480/330 are teaming up to thwart the function in some way. Would be interesting to know. Also, sure would be nice if they'd get their 480/330 interfaces figured out so they can drop the whole GDC34A altogether and just read the serial direct. Tim Olson - RV-10 N104CD - Flying Mike wrote: > --> Avionics-List message posted by: "Mike" > > I have the equipment, but like you am debugging. It's in and flying but > I can't get it to work.. > > Mike > > -----Original Message----- > From: owner-avionics-list-server@matronics.com > [mailto:owner-avionics-list-server@matronics.com] On Behalf Of Tim Olson > Sent: Tuesday, February 21, 2006 9:07 AM > To: rv10-list@matronics.com; rv-list@matronics.com; > avionics-list@matronics.com > Subject: Avionics-List: GTX330 TIS with DAC GDC34A/Chelton > > --> Avionics-List message posted by: Tim Olson > > At one point on a list I had a reply from someone who > actually was using the GDC34A Arinc to serial converter > like I am to get TIS traffic on their Chelton or other > EFIS from the GTX330 Transponder. > > Right now that's my last remaining thing to debug that > I've identified, and I'm hoping to talk to someone > who's got it working to verify settings. > > Anyone out there with that equipment that can comment? >