Today's Message Index:
----------------------
1. 07:22 AM - Re: Connector for P-1000 (Noel Loveys)
2. 10:55 AM - Re: Avionics-List Digest: 3 Msgs - 05/12/08 (D Wysong)
3. 11:59 AM - Re: Re: Avionics-List Digest: 3 Msgs - 05/12/08 (Doug McNutt)
4. 12:35 PM - Re: Re: Avionics-List Digest: 3 Msgs - 05/12/08 (Richard Tasker)
5. 05:28 PM - autopilot (Dennis Holbrook)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Connector for P-1000 |
Try Aviall or ant avionics shop.
Noel
From: owner-avionics-list-server@matronics.com
[mailto:owner-avionics-list-server@matronics.com] On Behalf Of Robin Hou
Sent: Tuesday, May 13, 2008 12:19 AM
Subject: Avionics-List: Connector for P-1000
I have a Horizon Instruments, Inc. P-1000 Digital Engine Tachometer. It has
a 6-pin connector labeled "Amphenol 14S-6PF". Does anyone have a source to
buy a matching connector to build its hardness? Also, anyone has pin-out
for this unit?
Thanks in advance.
Robin Hou
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Avionics-List Digest: 3 Msgs - 05/12/08 |
> I have a Horizon Instruments, Inc. P-1000 Digital Engine Tachometer. It has
a
> 6-pin connector labeled "Amphenol 14S-6PF". Does anyone have a source to buy
> a matching connector to build its hardness?
Hello Robin,
Try www.mouser.com and search for "amphenol 14S-6". They will point
you to their catalog and Amphenol datasheets that will assist you in
finding a mating connector.
D
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Avionics-List Digest: 3 Msgs - 05/12/08 |
At 11:51 -0600 5/13/08, D Wysong wrote:
>
>> I have a Horizon Instruments, Inc. P-1000 Digital Engine Tachometer. It has
a
>> 6-pin connector labeled "Amphenol 14S-6PF". Does anyone have a source to buy
>> a matching connector to build its hardness?
>
>Hello Robin, #!
>
>Try www.mouser.com and search for "amphenol 14S-6". They will point
>you to their catalog and Amphenol datasheets that will assist you in
>finding a mating connector.
I have in my hands an MS3106A - 14S -6S, A relic of World War II, in my hands.
Pins are letters A through F with pin A aligned with the alignment slot.
Where are you. Anywhere near Colorado Springs?
Digikey lists a mate to your connector but they have a $25 minimum charge. I donno
about Mouser. You'll need a cable clamp to go with it.
Hit me off line at dmcnutt@ (the from line) Colorado Springs, CO, US of A.
--
--> From the U S of A, the only socialist country that refuses to admit it. <--
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Avionics-List Digest: 3 Msgs - 05/12/08 |
Digikey doesn't actually have a $25 minimum. What they have is a $5
extra handling charge if your order is less than $25.
Mouser has no minimum charge or handling charge - but their prices are
typically a little higher.
Dick Tasker
Doug McNutt wrote:
>
> At 11:51 -0600 5/13/08, D Wysong wrote:
>
>>
>>
>>> I have a Horizon Instruments, Inc. P-1000 Digital Engine Tachometer. It has
a
>>> 6-pin connector labeled "Amphenol 14S-6PF". Does anyone have a source to
buy
>>> a matching connector to build its hardness?
>>>
>> Hello Robin, #!
>>
>> Try www.mouser.com and search for "amphenol 14S-6". They will point
>> you to their catalog and Amphenol datasheets that will assist you in
>> finding a mating connector.
>>
>
> I have in my hands an MS3106A - 14S -6S, A relic of World War II, in my hands.
Pins are letters A through F with pin A aligned with the alignment slot.
>
> Where are you. Anywhere near Colorado Springs?
>
> Digikey lists a mate to your connector but they have a $25 minimum charge. I
donno about Mouser. You'll need a cable clamp to go with it.
>
> Hit me off line at dmcnutt@ (the from line) Colorado Springs, CO, US of A.
>
>
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
To the many folks who responded to my autopilot questions... Thanks!
All good info on a variety of equipment. Apparently, there is no bad
choice... other than not installing an autopilot at all.
Dennis
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|