Today's Message Index:
----------------------
1. 09:33 AM - Re: crimping with a dmc af8 crimping tool (Ron Quillin)
2. 10:07 AM - Re: crimping with a dmc af8 crimping tool (keithmckinley)
3. 10:09 AM - crimping with a dmc af8 crimping tool (Beckman, Rick)
4. 10:43 AM - Re: crimping with a dmc af8 crimping tool (Ron Raby)
5. 11:39 AM - Re: crimping with a dmc af8 crimping tool (Ron Quillin)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: crimping with a dmc af8 crimping tool |
At 16:40 1/12/2010, you wrote:
>Just looking for the proper method of inserting the pin to be
>crimped as well as what a good test for the quality of the crimp should be.
>
>I do not have a g-125 gage to calibrate with. Also, do not have more
>than a couple pins to practice with.
The G-125, aka, M22520/3-1 can be used to test crimp depth for both
the small AFM-8 M22520/2-01 and large AF-8 M22520/1-01 crimpers. The
NO-GO diameter is 0.0440 dia and the GO is 0.0390 dia.
Use SEL 4 for the /1-01 and SEL 8 for the /2-01 tools.
Plug gauges can be purchased from McMaster-Carr at this page
http://www.mcmaster.com/#plug-gauges/=5cx5qj
using these part numbers
23055A039
23065A044
for $3.06 each.
The G-125 tool is little more than a dual ended collet holder for
these plug gauges with the above instructions...
Ron Q.
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: crimping with a dmc af8 crimping tool |
Thanks Ron! Above and beyond!
Keith
--------
Keith McKinley
700HS
KFIT
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=281294#281294
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | crimping with a dmc af8 crimping tool |
Just looking for the proper method of inserting the pin to be crimped as
well as what a good test for the quality of the crimp should be.
After the crimp is completed, give it a good pull test
Don't try to destroy it, but give a good firm pull.
Do NOT archive
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: crimping with a dmc af8 crimping tool |
Here is a document on crimping.
Regards
Ron Raby
Lancair ES
----- Original Message -----
From: Beckman, Rick
To: avionics-list@matronics.com
Sent: Wednesday, January 13, 2010 1:09 PM
Subject: Avionics-List: crimping with a dmc af8 crimping tool
Just looking for the proper method of inserting the pin to be crimped
as well as what a good test for the quality of the crimp should be.
After the crimp is completed, give it a good pull test
Don't try to destroy it, but give a good firm pull.
Do NOT archive
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: crimping with a dmc af8 crimping tool |
Some time ago on the aeroelectric list I posted and I believe Bob
archived some NASA how-to documents on various wiring practices,
among them harness fabrication and wire terminations. Included were
accepted procedures to insure reliable crimps.
>To: aeroelectric-list@matronics.com
>From: "Robert L. Nuckolls, III" <nuckolls.bob@aeroelectric.com>
>Subject: Re: AeroElectric-List: NASA docs
>
>--> AeroElectric-List message posted by: "Robert L. Nuckolls, III"
><nuckolls.bob@aeroelectric.com>
>
>At 12:48 PM 6/28/2009, you wrote:
>>Bob,
>>
>>The current editions I teach from...
>>
>>http://www.hq.nasa.gov/office/codeq/doctree/87391.htm
>>http://www.hq.nasa.gov/office/codeq/doctree/87392.htm
>>http://www.hq.nasa.gov/office/codeq/doctree/87393.htm
>>http://www.hq.nasa.gov/office/codeq/doctree/87394.htm
>>
>>Ron Q.
>
> Thanks! I'll update my library as well as the website
> posting.
>
>
> Bob . . .
At 10:34 1/13/2010, you wrote:
>Here is a document on crimping.
>
>Regards
>
>Ron Raby
>
>Lancair ES
>----- Original Message -----
>From: <mailto:Rick.Beckman@atk.com>Beckman, Rick
>To: <mailto:avionics-list@matronics.com>avionics-list@matronics.com
>Sent: Wednesday, January 13, 2010 1:09 PM
>Subject: Avionics-List: crimping with a dmc af8 crimping tool
>
>
>Just looking for the proper method of inserting the pin to be
>crimped as well as what a good test for the quality of the crimp should be.
>
>
> After the crimp is completed, give it a good pull
> test Don't try to destroy it, but give a good firm pull.
>
>
> Do NOT archive
>
>
>href="http://www.matronics.com/Navigator?Avionics-List">http://www.matronics.com/Navigator?Avionics-List
>
>href="http://forums.matronics.com">http://forums.matronics.com
>
>href="http://www.matronics.com/contribution">http://www.matronics.com/c
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|