Today's Message Index:
----------------------
1. 03:35 AM - Re: Narco COM11/11A/120 Tray Connectors (Bill Henderson)
2. 04:36 AM - Re: Question on PS6000/SL-10 Audio Panel (Ralph E. Capen)
3. 07:36 AM - Re: Looking for info on GPS-50/60/65 (David Bridgham)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Narco COM11/11A/120 Tray Connectors |
Don't know if this place has what you're looking for, but I found a
connector that fits a KT-76A cheap.....
http://www.mikesarcade.com/cgi-bin/store.pl?sku=CECM24
It's a gamming store, but who cares if you can find what you need.
Bill
----- Original Message -----
From: "okiairboss" <boss@adaairexpo.com>
Sent: Tuesday, April 27, 2010 11:58 PM
Subject: Avionics-List: Narco COM11/11A/120 Tray Connectors
>
> I am looking for qty 2 Molex white single sided 15 pin Narco tray
> connectors. Can be out of salvage and missing pins. Needed for ground
> based air boss rig.
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=295966#295966
>
>
>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Question on PS6000/SL-10 Audio Panel |
I have the PMA7000MS (UPSAT SL15). When I was going through the integration of
my stereo system, I remember reading the requirement for low level input:
"NOTE: Use the low level output of any entertainment device to connect to the audio
panel. Maximum signal level is 2 VAC p-p.
DO NOT use a speaker-level output, this will cause internal damage in the audio
panel."
There is a minimum power requirement for operation though:
"The audio signal at the entertainment input must be a minimum of 500 mV P-P per
channel for optimum music performance."
The first one of these criteria was a limiting factor in my selection of audio
inputs...I have a Sony AM/FM/CD/MP3 player attached to my audio panel (as it output
the corect voltage levels)...the Sony has inputs to take iPods or whatever
else so I am adding that type of equipment through the Sony.
Ralph
RV6A N822AR @ N06 - 60 hours....just getting to installing the main wheel pants....
-----Original Message-----
>From: DEAN PSIROPOULOS <dean.psiropoulos@verizon.net>
>Sent: Apr 27, 2010 10:33 PM
>To: avionics-list@matronics.com
>Subject: Avionics-List: Question on PS6000/SL-10 Audio Panel
>
>
>
>My PS engineering 6000 (mfg for UPS AT as the SL-10 MS) intercom has stereo
>audio inputs and outputs. The other day I was flying and finally plugged in
>my Sandisk mp3 player to enjoy some music while working my airspeed
>calibration runs. I had the Sandisk volume set at maximum and had to have
>the volume on the PS 6000 at 3/4 maximum to hear the music at a low level.
>Also the music sounded a little distorted (not too surprising given the
>volume setting on the 6000). I was hoping that there would be a pot on the
>circuit board that I could adjust to increase the input sensitivity but
>couldn't find anything in the manual about it. The system is set up for
>stereo but right now I'm running the mono Sigtronics headset that I
>purchased during my "Cessna" days, I have the volume on the headset at
>maximum when doing the above test. The 6000 manual says it's ok to plug in
>mono headsets so I doubt that the system has been damaged in any way.
>Anyone have some words of wisdom on running mp3 and other audio input
>devices with aviation intercoms and audio panels? I assumed the audio
>inputs needed high level (not speaker level inputs) but maybe the Sandisk
>just doesn't have enough oomph. In the short term I plan to convert the mono
>headset to Stereo, long term I plan to purchase an ANR Stereo headset of
>excellent quality (and unfortunately price). Please advise. Thanks.
>
>Dean Psiropoulos
>RV-6A N197DM
>Flying and finishing touches
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Looking for info on GPS-50/60/65 |
I haven't run down to the airport to try this out, but my manual says:
Press SYS
Large knob to Navigation Info, press Enter
Large knob to Program Nav Pages, press Enter
If I'm reading this right, it should show "Nav Mode Display -
Programmable and -- Autonav Pages *".
Use the Small Knob to reach a programmable Nav page.
Press SEL to start field selection. Turn the Large Knob to the desired
field.
Turn the Small Knob to select the units you want.
Press Enter to save that change or Sel to ignore the change.
Yup, never would have guessed all that.
If it doesn't work, I'll try it out on my GX-60 and get better
instructions. Good luck.
-Dave
On 04/27/2010 09:53 PM, DEAN PSIROPOULOS wrote:
>
>
> Has anyone with a UPS AT GX-50/60/65 panel mount GPS been able to change the
> ground speed readout from knots to MPH? I'm trying to finish a ground speed
> calibration series and it would be easier if the flight instruments and GPS
> had the same speed readout. I looked through the installation and operating
> manuals and didn't find any information on changing KNOTS to MPH. Anyone
> ever done this? If so how did you do it?
>
> Dean Psiropoulos
> RV-6A N197DM
> Flying and finishing touches
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|