Today's Message Index:
----------------------
1. 07:20 PM - Re: Help with Gns 480 Century HSI (Ron Quillin)
2. 07:52 PM - Re: Help with Gns 480 Century HSI (Dan Bergeron)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Help with Gns 480 Century HSI |
Many comments on the Yahoo 480 group regarding poor seating/mating in
the mounting tube.
Make sure it is secure, fully engaged. Even 1/32" makes a difference.
Ron Q.
At 15:17 7/4/2011, you wrote:
>I have a CNX-80 - GNS480 witht he following other units. Century
>1000 HSI, MX20, SL15.
>I had the GNS 480 software upgrade, since then I am not getting any
>CDI function on the HSI. the VDI etc, still works, but not CDI.
>I have checked my setup and all seems OK to me - but I may be
>missing something.
>Also, Altitude does not display on MX 20 - have an SL70 remote
>transponder - output from GNS 480 is showing correct altitude.
>
>Any GNS 480 experts, help would be appreciated. Avionics shop where
>I had the upgrade done is not homebuilder friendly.
>
>Dave Burnham
>RV6A - N64FN - flying since 2006
>
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Help with Gns 480 Century HSI |
Dave:
I've been flying my RV-7A for nearly two years, I have a Garmin 480 as my
primary radio - probably one of the last ones to come off the production
line - took me a long time to get comfortable with it - not terribly user
friendly - have finally done it - it's a great radio - amazing capability.
A couple of months ago I kept losing GPS function - I'd be in the middle of
an approach or in cruise - suddenly - nothing - my long time mentor
suggested sliding the radio partially out of the rack and reseating it -
push firmly on the four corners of the case - then snug it down real good
with the allen wrench - haven't had a problem since - I carry the allen
wrench in the side pocket by my left elbow - every couple of weeks I snug
the set screw down.
Just a suggestion -
Dan Bergeron
RV-7A - N307TB
247 hours since first flight on 8/4/09
On Mon, Jul 11, 2011 at 10:16 PM, Ron Quillin <rjquillin@cox.net> wrote:
> Many comments on the Yahoo 480 group regarding poor seating/mating in the
> mounting tube.
> Make sure it is secure, fully engaged. Even 1/32" makes a difference.
>
> Ron Q.
> At 15:17 7/4/2011, you wrote:
>
> I have a CNX-80 - GNS480 witht he following other units. Century 1000 HSI,
> MX20, SL15.
> I had the GNS 480 software upgrade, since then I am not getting any CDI
> function on the HSI. the VDI etc, still works, but not CDI.
> I have checked my setup and all seems OK to me - but I may be missing
> something.
> Also, Altitude does not display on MX 20 - have an SL70 remote transponder
> - output from GNS 480 is showing correct altitude.
>
> Any GNS 480 experts, help would be appreciated. Avionics shop where I had
> the upgrade done is not homebuilder friendly.
>
> Dave Burnham
> RV6A - N64FN - flying since 2006
>
> *
>
> *
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|