Avionics-List Digest Archive

Wed 07/06/16


Total Messages Posted: 1



Today's Message Index:
----------------------
 
     1. 11:33 AM - Re: MX-20 connected to 400W/500W - UPDATE (Ralph E. Capen)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 11:33:43 AM PST US
    From: "Ralph E. Capen" <recapen@earthlink.net>
    Subject: Re: MX-20 connected to 400W/500W - UPDATE
    Just to keep everyone in the loop.... There are multiple valid output protocols from the 400W/500W series that work with the MX-20...some have more features than others - the differences are not spelled out in the installation manuals. Got with the folks at Stark Aviation (I bought most of my gear through his shop), he was able to get an understanding of the differences and pass them to me. I was using "Aviation" as the output protocol from my 420W as it is acceptable to both the MX20 and my AFS3400s EFIS. Come to find out, the software upgrades changed some of the bits making this one a less viable option. I need to use "MXMap" for the MX20 and wire up two more outputs from the 420W...one for the EFIS and another for the ADS-600B -----Original Message----- >From: "Ralph E. Capen" <recapen@earthlink.net> >Sent: Jul 5, 2016 1:19 PM >To: rv-list <rv-list@matronics.com>, "avionics-list@matronics.com" <avionics-list@matronics.com> >Subject: RV-List: MX-20 connected to 400W/500W > >--> RV-List message posted by: "Ralph E. Capen" <recapen@earthlink.net> > >Any of you out there using the MX-20 connected to either a 400W or 500W series GPS? > >I have a 420W connected to a MX-20. Recently upgraded the software in the 420W and now the MX-20 screen map area is blank with the red X in the middle unless I have a flight plan active. I have verified my wiring and settings - along with the system showing my position with the flight plan active so i am confident in the wiring / settings. > >The 420W is running 5.3/5.0 software and the MX-20 has been tested up to version 5.7. My understanding is that a newer version of software is available for the MX-20 and I am making inquiries as to upgrading. My question to other users is - Does it work with the later software - or did Garmin abandon this device already!? > >Thanks, >Ralph Capen




    Other Matronics Email List Services

  • Post A New Message
  •   avionics-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/Avionics-List.htm
  • Web Forum Interface To Lists
  •   http://forums.matronics.com
  • Matronics List Wiki
  •   http://wiki.matronics.com
  • 7-Day List Browse
  •   http://www.matronics.com/browse/avionics-list
  • Browse Avionics-List Digests
  •   http://www.matronics.com/digest/avionics-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contribution

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --