Today's Message Index:
----------------------
1. 05:37 PM - flyin (Chris Schuermann)
2. 06:22 PM - Re: flyin (MRP)
3. 06:28 PM - Re: flyin (Chris Schuermann)
4. 06:56 PM - Re: flyin (Martini Luc J.R.)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
--> Commander-List message posted by: Chris Schuermann <cschuerm@cox.net>
Anyone have any details on what the seminars are going to be for this
years fly-in and who will be speaking?
Any of my old friends going to be there?
chris
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
--> Commander-List message posted by: MRP <mrp37@mindspring.com>
Hey Chris,
Mark Poulin from Carolina. I haven't seen you since "Hillsboro". I tried to make
it the last to years and was not able to. Hopefully this year!?!
Have you ever found anything to replace your Bellanca?
Best Regards,
Mark
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
--> Commander-List message posted by: Chris Schuermann <cschuerm@cox.net>
MRP wrote:
> Hey Chris,
> Have you ever found anything to replace your Bellanca?
Hey Mark!
Good to hear from you. I didn't know you were still around and on the
list. I made the S.C. flyin, but missed last year. Just a bit too much
trauma and too few $$$ available.
Yes, I did acquire a new project/airplane - take a look at:
http://members.cox.net/cschuerm/
and tell me what you think.
cheers
chris
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
--> Commander-List message posted by: "Martini Luc J.R." <martini@foxinternet.net>
Hi
I sure would like to know what you used to get the old paint off your
projects.
While your at it, you might tell me about how you neutralized the Paint
Stripper caustic compounds (I've heard flusing with a lot of water just
doesn't hack it, because residue caught in lap joints etc, will only cause
the New Paint in those areas to deteriorate and probably result in
corrosion.
And, since I haven't asked anything hard so far ..... tell me all about how
NOT to remove paint. I have heard of horror stories resulting from using
wirebrushes (however soft, i.e. fine steel or brass wire brush, particular
rotary types) on ALCLAD Aluminum, which even after subsequently being
Allodined and receiving a good paint job, resulted in severe granular
corrosion setting in over a matter of only a couple of years. I know the
preferred thing to use is ScotchbritePads... Is there anything available to
help get into tight places like an ALUMINUM WIRE BRUSH that could be used
instead of a STEEL wire brush?
EAA had an article on Corrosion a few months back, but I gave my copy away,
and now can't find it anywhere so I can REREAD the advise..... although I
don't think they said much about what using a Steel Brush will do to ALCLAD.
----- Original Message -----
From: "Chris Schuermann" <cschuerm@cox.net>
Subject: Re: Commander-List: flyin
> --> Commander-List message posted by: Chris Schuermann <cschuerm@cox.net>
>
>
> MRP wrote:
> > Hey Chris,
> > Have you ever found anything to replace your Bellanca?
>
> Hey Mark!
> Good to hear from you. I didn't know you were still around and on the
> list. I made the S.C. flyin, but missed last year. Just a bit too much
> trauma and too few $$$ available.
> Yes, I did acquire a new project/airplane - take a look at:
> http://members.cox.net/cschuerm/
> and tell me what you think.
>
> cheers
> chris
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|