---------------------------------------------------------- Commander-List Digest Archive --- Total Messages Posted Wed 06/23/04: 4 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 05:37 PM - flyin (Chris Schuermann) 2. 06:22 PM - Re: flyin (MRP) 3. 06:28 PM - Re: flyin (Chris Schuermann) 4. 06:56 PM - Re: flyin (Martini Luc J.R.) ________________________________ Message 1 _____________________________________ Time: 05:37:21 PM PST US From: Chris Schuermann Subject: Commander-List: flyin --> Commander-List message posted by: Chris Schuermann Anyone have any details on what the seminars are going to be for this years fly-in and who will be speaking? Any of my old friends going to be there? chris ________________________________ Message 2 _____________________________________ Time: 06:22:42 PM PST US From: MRP Subject: Re: Commander-List: flyin --> Commander-List message posted by: MRP Hey Chris, Mark Poulin from Carolina. I haven't seen you since "Hillsboro". I tried to make it the last to years and was not able to. Hopefully this year!?! Have you ever found anything to replace your Bellanca? Best Regards, Mark ________________________________ Message 3 _____________________________________ Time: 06:28:25 PM PST US From: Chris Schuermann Subject: Re: Commander-List: flyin --> Commander-List message posted by: Chris Schuermann MRP wrote: > Hey Chris, > Have you ever found anything to replace your Bellanca? Hey Mark! Good to hear from you. I didn't know you were still around and on the list. I made the S.C. flyin, but missed last year. Just a bit too much trauma and too few $$$ available. Yes, I did acquire a new project/airplane - take a look at: http://members.cox.net/cschuerm/ and tell me what you think. cheers chris ________________________________ Message 4 _____________________________________ Time: 06:56:28 PM PST US From: "Martini Luc J.R." Subject: Re: Commander-List: flyin --> Commander-List message posted by: "Martini Luc J.R." Hi I sure would like to know what you used to get the old paint off your projects. While your at it, you might tell me about how you neutralized the Paint Stripper caustic compounds (I've heard flusing with a lot of water just doesn't hack it, because residue caught in lap joints etc, will only cause the New Paint in those areas to deteriorate and probably result in corrosion. And, since I haven't asked anything hard so far ..... tell me all about how NOT to remove paint. I have heard of horror stories resulting from using wirebrushes (however soft, i.e. fine steel or brass wire brush, particular rotary types) on ALCLAD Aluminum, which even after subsequently being Allodined and receiving a good paint job, resulted in severe granular corrosion setting in over a matter of only a couple of years. I know the preferred thing to use is ScotchbritePads... Is there anything available to help get into tight places like an ALUMINUM WIRE BRUSH that could be used instead of a STEEL wire brush? EAA had an article on Corrosion a few months back, but I gave my copy away, and now can't find it anywhere so I can REREAD the advise..... although I don't think they said much about what using a Steel Brush will do to ALCLAD. ----- Original Message ----- From: "Chris Schuermann" Subject: Re: Commander-List: flyin > --> Commander-List message posted by: Chris Schuermann > > > MRP wrote: > > Hey Chris, > > Have you ever found anything to replace your Bellanca? > > Hey Mark! > Good to hear from you. I didn't know you were still around and on the > list. I made the S.C. flyin, but missed last year. Just a bit too much > trauma and too few $$$ available. > Yes, I did acquire a new project/airplane - take a look at: > http://members.cox.net/cschuerm/ > and tell me what you think. > > cheers > chris > >