---------------------------------------------------------- Commander-List Digest Archive --- Total Messages Posted Sat 01/28/12: 3 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 09:48 AM - Re: Hyd. Motor for Pres. (gmosh@charter.net) 2. 10:19 AM - Re: Hyd. Motor for Pres. (Donnie Rose) 3. 02:55 PM - Re: Hyd. Motor for Pres. (Tylor Hall) ________________________________ Message 1 _____________________________________ Time: 09:48:43 AM PST US From: gmosh@charter.net Subject: RE: Commander-List: Hyd. Motor for Pres. Moe, Unless absolutely necessary, no design engineer would utilize specialized bearings in an assembly if a suitable one was available off the shelf. The cost of producing a special bearing produced in small numbers would be prohibitive. The bearing will likely sport a chemically etched part # on the race which you can use to find the replacement. With a little research, you should be able to find the bearing you need. {Never under any circumstances tell the bearing supplier its for an airplane....."It's for my garden tractor"} I have successfully sourced seals, bearings etc. for my Commander from manufactures catalogs. I needed a seal for the gear box which I purchased from an engine re builder. The Chicago Rawhide package the seal came in was unopened (from the factory); was obviously not inspected (I wasn't surprised!) by Lycoming and the package simply stamped with the Lycoming part number and of course - marked up astronomically. Hope this helps. Gary N206DX On Fri, Jan 27, 2012 at 7:02 PM, Stan wrote: Hi Moe, Is it possible that the roller bearing is an industry standard part? And if the bearing is chattering, how is the shaft holding up? Regards, Stan From: owner-commander-list-server@matronics.com [mailto:owner-commander-list-server@matronics.com] On Behalf Of Moe Mills Sent: Friday, January 27, 2012 3:37 PM Subject: Commander-List: Hyd. Motor for Pres. Hi folks, I need a serviceable Vickers Hydraulic Motor for the primary pressurization supercharger on my 680F(p). The part number on the motor tag is MF03380078. If you do not have a complete motor, I really only need the roller bearing inside the pump. My pump still puts out good pressure, it's just that it is so noisy that even drivers of early Lears complain about the noise on the tarmac. Regards, Moe Mills N680RR Cell # (310) 350-4594 http://www.matronics.com/Navigator?Commander-List http://forums.matronics.com http://www.matronics.com/contribution ________________________________ Message 2 _____________________________________ Time: 10:19:52 AM PST US From: Donnie Rose Subject: Re: Commander-List: Hyd. Motor for Pres. Amen Gary! I have great luck with "Motion Industries" for both brgs and sea ls.=0A=0A=0ADonnie Rose =0A205/492-8444=0A=0A=0A=0A>_______________________ _________=0A>From: "gmosh@charter.net" =0A>To: commander -list@matronics.com =0A>Sent: Saturday, January 28, 2012 11:46 AM=0A>Subjec t: RE: Commander-List: Hyd. Motor for Pres.=0A>=0A>=0A>Moe,=0A>=0A>Unless a bsolutely necessary, no design engineer would utilize specialized bearings in an assembly if a suitable one was available off the shelf.- The cost o f producing a special bearing produced in small numbers would be prohibitiv e.- The bearing will likely sport a chemically etched part # on the race which you can use to find the replacement.- With a little research, you s hould be able to find the bearing you need.- {Never under any circumstanc es tell the bearing supplier its for an airplane....."It's for my garden tr actor"}- =0A>=0A>I have successfully sourced seals, bearings etc. for my Commander from manufactures catalogs.- I needed a seal for the gear box w hich I purchased from an engine re builder.- The Chicago Rawhide package the seal came in was unopened (from the factory); was obviously not inspect ed (I wasn't surprised!) by Lycoming and the package simply stamped with th e Lycoming part number and of course - marked up astronomically.=0A>=0A>Hop e this helps.=0A>=0A>Gary=0A>N206DX---- =0A>=0A>=0A>On Fri, Jan 27, 2012 at 7:02 PM, Stan wrote:=0A>=0A>-Hi Moe, =0A>- =0A>Is it possible that the roller bearing is an industry standard part? And if the bearing is chattering, how is the shaft holding up? =0A>- =0A>Regards, =0A>Stan =0A >- =0A>From: owner-commander-list-server@matronics.com [mailto:owner-comm ander-list-server@matronics.com] On Behalf Of Moe Mills =0A>Sent: Friday, J anuary 27, 2012 3:37 PM =0A>To: Com =0A>Subject: Commander-List: Hyd. Motor for Pres. =0A>- =0A>Hi folks, =0A>- =0A>I need a serviceable Vickers H ydraulic Motor for the primary pressurization supercharger on my 680F(p). - The part number on the motor tag is MF03380078.- If you do not have a complete motor, I really only need the roller bearing inside the pump.- My pump still puts out good pressure, it's just that it is so noisy that ev en drivers of early Lears complain about the noise on the tarmac. =0A>- =0A>Regards, =0A>- =0A>Moe Mills =0A>N680RR =0A>Cell # (310) 350-4594 =0A >- =0A>--- http://www.matronics.com/Navigator?Commander-List http:/ /forums.matronics.com http://www.matronics.com/contribution-- =0A>ww.ma tronics.com/Navigator?Commander-List" TARGET="_blank">http://wONT>=0A>nbs p;-- - MATRONICS WEB FORUMS -=0A><-- --> http://forums.matronics.co mhttp://www.matronics.com/contributionhttp://www.matronics.com/Navigator?Co ________________________________ Message 3 _____________________________________ Time: 02:55:27 PM PST US From: Tylor Hall Subject: Re: Commander-List: Hyd. Motor for Pres. Moe, There is a Motion Industries in Farmington, NM I buy lots of stuff from them from the the ABQ store. Tylor Hall On Jan 28, 2012, at 10:46 AM, gmosh@charter.net wrote: > Moe, > > Unless absolutely necessary, no design engineer would utilize specialized bearings in an assembly if a suitable one was available off the shelf. The cost of producing a special bearing produced in small numbers would be prohibitive. The bearing will likely sport a chemically etched part # on the race which you can use to find the replacement. With a little research, you should be able to find the bearing you need. {Never under any circumstances tell the bearing supplier its for an airplane....."It's for my garden tractor"} > > I have successfully sourced seals, bearings etc. for my Commander from manufactures catalogs. I needed a seal for the gear box which I purchased from an engine re builder. The Chicago Rawhide package the seal came in was unopened (from the factory); was obviously not inspected (I wasn't surprised!) by Lycoming and the package simply stamped with the Lycoming part number and of course - marked up astronomically. > > Hope this helps. > > Gary > N206DX > > > On Fri, Jan 27, 2012 at 7:02 PM, Stan wrote: > > Hi Moe, > > Is it possible that the roller bearing is an industry standard part? And if the bearing is chattering, how is the shaft holding up? > > Regards, > Stan > > From: owner-commander-list-server@matronics.com [mailto:owner-commander-list-server@matronics.com] On Behalf Of Moe Mills > Sent: Friday, January 27, 2012 3:37 PM > To: Com > Subject: Commander-List: Hyd. Motor for Pres. > > Hi folks, > > I need a serviceable Vickers Hydraulic Motor for the primary pressurization supercharger on my 680F(p). The part number on the motor tag is MF03380078. If you do not have a complete motor, I really only need the roller bearing inside the pump. My pump still puts out good pressure, it's just that it is so noisy that even drivers of early Lears complain about the noise on the tarmac. > > Regards, > > Moe Mills > N680RR > Cell # (310) 350-4594 > > http://www.matronics.com/Navigator?Commander-List http://forums.matronics.com http://www.matronics.com/contribution > ww.matronics.com/Navigator?Commander-List" TARGET="_blank">http://wONT> > nbsp; - MATRONICS WEB FORUMS - > < --> http://forums.matronics.com > http://www.matronics.com/contribution > > > ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message commander-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Commander-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/commander-list Browse Digests http://www.matronics.com/digest/commander-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.