Today's Message Index:
----------------------
1. 09:28 AM - Re: Hyd. Motor for Pres. (Moe Mills)
2. 09:31 AM - Re: Hyd. Motor for Pres. (Moe Mills)
3. 09:45 AM - Re: Hyd. Motor for Pres. (Stan)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Hyd. Motor for Pres. |
Thanks guys=2C I was "Trolling".
Tyler=2C Motion Industries is good=2C however=2C for machinery parts and so
fourth I seem to be better off at Animus Bearing.
Regards=2C
Moe
N680RR
From: tylorhall@mac.com
Subject: Re: Commander-List: Hyd. Motor for Pres.
Moe=2C
There is a Motion Industries in Farmington=2C NM
I buy lots of stuff from them from the the ABQ store.
Tylor Hall
On Jan 28=2C 2012=2C at 10:46 AM=2C gmosh@charter.net wrote:
Moe=2C
Unless absolutely necessary=2C no design engineer would utilize specialized
bearings in an assembly if a suitable one was available off the shelf. Th
e cost of producing a special bearing produced in small numbers would be pr
ohibitive. The bearing will likely sport a chemically etched part # on the
race which you can use to find the replacement. With a little research=2C
you should be able to find the bearing you need. {Never under any circums
tances tell the bearing supplier its for an airplane....."It's for my garde
n tractor"}
I have successfully sourced seals=2C bearings etc. for my Commander from ma
nufactures catalogs. I needed a seal for the gear box which I purchased fr
om an engine re builder. The Chicago Rawhide package the seal came in was
unopened (from the factory)=3B was obviously not inspected (I wasn't surpri
sed!) by Lycoming and the package simply stamped with the Lycoming part num
ber and of course - marked up astronomically.
Hope this helps.
Gary
N206DX
On Fri=2C Jan 27=2C 2012 at 7:02 PM=2C Stan wrote:
Hi Moe=2C
Is it possible that the roller bearing is an industry standard part? And if
the bearing is chattering=2C how is the shaft holding up?
Regards=2C
Stan
From: owner-commander-list-server@matronics.com [mailto:owner-commander-lis
t-server@matronics.com] On Behalf Of Moe Mills
Sent: Friday=2C January 27=2C 2012 3:37 PM
Subject: Commander-List: Hyd. Motor for Pres.
Hi folks=2C
I need a serviceable Vickers Hydraulic Motor for the primary pressurization
supercharger on my 680F(p). The part number on the motor tag is MF0338007
8. If you do not have a complete motor=2C I really only need the roller be
aring inside the pump. My pump still puts out good pressure=2C it's just t
hat it is so noisy that even drivers of early Lears complain about the nois
e on the tarmac.
Regards=2C
Moe Mills
N680RR
Cell # (310) 350-4594
http://www.matronics.com/Navigator?Commander-List http://forums.matroni
cs.com http://www.matronics.com/contribution
ww.matronics.com/Navigator?Commander-List" TARGET="_blank">http://wONT>
nbsp=3B - MATRONICS WEB FORUMS -
< --> http://forums.matronics.com
http://www.matronics.com/contribution
face="courier new=2Ccourier">http://www.matronics.com/Navigator?Commander
-List
href="http://forums.matronics.com/">http://forums.matronics.com
href="http://www.matronics.com/contribution">http://www.matronics.com/con
tribution
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Hyd. Motor for Pres. |
From: swperk@earthlink.net
Subject: RE: Commander-List: Hyd. Motor for Pres.
Hi Moe=2C
Is it possible that the roller bearing is an industry standard part? And if
the bearing is chattering=2C how is the shaft holding up?
Regards=2C
Stan
From: owner-commander-list-server@matronics.com [mailto:owner-commander-lis
t-server@matronics.com] On Behalf Of Moe Mills
Sent: Friday=2C January 27=2C 2012 3:37 PM
Subject: Commander-List: Hyd. Motor for Pres.
Hi folks=2C
I need a serviceable Vickers Hydraulic Motor for the primary pressurization
supercharger on my 680F(p). The part number on the motor tag is MF0338007
8. If you do not have a complete motor=2C I really only need the roller be
aring inside the pump. My pump still puts out good pressure=2C it's just t
hat it is so noisy that even drivers of early Lears complain about the nois
e on the tarmac.
Regards=2C
Moe Mills
N680RR
Cell # (310) 350-4594
< - The Commander-List Email Forum -http://www.matronics.com/Nav
igator?Commander-Listhttp://forums.matronics.comhttp://www.matronics.com/co
ntribution
Hi Stan=2C Thanks for the input. I was "Trolling". Hope all is well in yo
ur world=2C tell Bob I said Hi. Moe N680RR
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Hyd. Motor for Pres. |
Hi Moe,
I just did, and he sends his regards right back to you!
Stan
Hi Stan,
Thanks for the input. I was "Trolling". Hope all is well in your world,
tell Bob I said Hi.
Moe
N680RR
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|