---------------------------------------------------------- Commander-List Digest Archive --- Total Messages Posted Sun 01/29/12: 3 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 09:28 AM - Re: Hyd. Motor for Pres. (Moe Mills) 2. 09:31 AM - Re: Hyd. Motor for Pres. (Moe Mills) 3. 09:45 AM - Re: Hyd. Motor for Pres. (Stan) ________________________________ Message 1 _____________________________________ Time: 09:28:09 AM PST US From: Moe Mills Subject: RE: Commander-List: Hyd. Motor for Pres. Thanks guys=2C I was "Trolling". Tyler=2C Motion Industries is good=2C however=2C for machinery parts and so fourth I seem to be better off at Animus Bearing. Regards=2C Moe N680RR From: tylorhall@mac.com Subject: Re: Commander-List: Hyd. Motor for Pres. Moe=2C There is a Motion Industries in Farmington=2C NM I buy lots of stuff from them from the the ABQ store. Tylor Hall On Jan 28=2C 2012=2C at 10:46 AM=2C gmosh@charter.net wrote: Moe=2C Unless absolutely necessary=2C no design engineer would utilize specialized bearings in an assembly if a suitable one was available off the shelf. Th e cost of producing a special bearing produced in small numbers would be pr ohibitive. The bearing will likely sport a chemically etched part # on the race which you can use to find the replacement. With a little research=2C you should be able to find the bearing you need. {Never under any circums tances tell the bearing supplier its for an airplane....."It's for my garde n tractor"} I have successfully sourced seals=2C bearings etc. for my Commander from ma nufactures catalogs. I needed a seal for the gear box which I purchased fr om an engine re builder. The Chicago Rawhide package the seal came in was unopened (from the factory)=3B was obviously not inspected (I wasn't surpri sed!) by Lycoming and the package simply stamped with the Lycoming part num ber and of course - marked up astronomically. Hope this helps. Gary N206DX On Fri=2C Jan 27=2C 2012 at 7:02 PM=2C Stan wrote: Hi Moe=2C Is it possible that the roller bearing is an industry standard part? And if the bearing is chattering=2C how is the shaft holding up? Regards=2C Stan From: owner-commander-list-server@matronics.com [mailto:owner-commander-lis t-server@matronics.com] On Behalf Of Moe Mills Sent: Friday=2C January 27=2C 2012 3:37 PM Subject: Commander-List: Hyd. Motor for Pres. Hi folks=2C I need a serviceable Vickers Hydraulic Motor for the primary pressurization supercharger on my 680F(p). The part number on the motor tag is MF0338007 8. If you do not have a complete motor=2C I really only need the roller be aring inside the pump. My pump still puts out good pressure=2C it's just t hat it is so noisy that even drivers of early Lears complain about the nois e on the tarmac. Regards=2C Moe Mills N680RR Cell # (310) 350-4594 http://www.matronics.com/Navigator?Commander-List http://forums.matroni cs.com http://www.matronics.com/contribution ww.matronics.com/Navigator?Commander-List" TARGET="_blank">http://wONT> nbsp=3B - MATRONICS WEB FORUMS - < --> http://forums.matronics.com http://www.matronics.com/contribution face="courier new=2Ccourier">http://www.matronics.com/Navigator?Commander -List href="http://forums.matronics.com/">http://forums.matronics.com href="http://www.matronics.com/contribution">http://www.matronics.com/con tribution ________________________________ Message 2 _____________________________________ Time: 09:31:41 AM PST US From: Moe Mills Subject: RE: Commander-List: Hyd. Motor for Pres. From: swperk@earthlink.net Subject: RE: Commander-List: Hyd. Motor for Pres. Hi Moe=2C Is it possible that the roller bearing is an industry standard part? And if the bearing is chattering=2C how is the shaft holding up? Regards=2C Stan From: owner-commander-list-server@matronics.com [mailto:owner-commander-lis t-server@matronics.com] On Behalf Of Moe Mills Sent: Friday=2C January 27=2C 2012 3:37 PM Subject: Commander-List: Hyd. Motor for Pres. Hi folks=2C I need a serviceable Vickers Hydraulic Motor for the primary pressurization supercharger on my 680F(p). The part number on the motor tag is MF0338007 8. If you do not have a complete motor=2C I really only need the roller be aring inside the pump. My pump still puts out good pressure=2C it's just t hat it is so noisy that even drivers of early Lears complain about the nois e on the tarmac. Regards=2C Moe Mills N680RR Cell # (310) 350-4594 < - The Commander-List Email Forum -http://www.matronics.com/Nav igator?Commander-Listhttp://forums.matronics.comhttp://www.matronics.com/co ntribution Hi Stan=2C Thanks for the input. I was "Trolling". Hope all is well in yo ur world=2C tell Bob I said Hi. Moe N680RR ________________________________ Message 3 _____________________________________ Time: 09:45:08 AM PST US From: "Stan" Subject: RE: Commander-List: Hyd. Motor for Pres. Hi Moe, I just did, and he sends his regards right back to you! Stan Hi Stan, Thanks for the input. I was "Trolling". Hope all is well in your world, tell Bob I said Hi. Moe N680RR ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message commander-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Commander-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/commander-list Browse Digests http://www.matronics.com/digest/commander-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.