Today's Message Index:
----------------------
1. 04:04 AM - =?utf-8?Q?Re:__Turnbuckles_ain=99t_cheap? (Jack Textor)
2. 01:40 PM - Re: Turnbuckles =?ISO-8859-1?Q?ain=99t?= cheap (danoliver)
3. 02:22 PM - =?utf-8?Q?Re:__Turnbuckles_ain=99t_cheap? (Jack Textor)
4. 07:07 PM - TIG Welding question (John Franklin)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: ?Q?Re:_Pietenpol-List:_Turnbuckles_ain=99t_cheap? |
Oscar you say it so much more eloquently than I!
Jack Textor
Sent from my iPad
> On Jun 3, 2018, at 11:02 PM, taildrags <taildrags@hotmail.com> wrote:
>
>
> Jack; by "wide crimpers", what are you referring to? The conventional nicopress
tool makes three crimps close to each other in the single ferrule, all in
one pass. The hardware store crimper, as well as the hand-operated crimper that
Aircraft Spruce and others sell and that makes the crimp by the use of a crescent
wrench, box- or open-end wrench (ratcheting or not) turning a pair of bolts
that tighten down the crimping mandrels onto the ferrule, makes a single
wide crimp on the ferrule. All of the nicopressed cable connections on my airplane
are made with the conventional triple-crimp except for the ones that I made
on the tail brace wires when I replaced the galvanized cables with stainless.
I didn't have the big cable-cutter looking tool to make the triple crimp
so I use the hand tool which makes just one wide crimp on the cables.
>
> --------
> Oscar Zuniga
> Medford, OR
> Air Camper NX41CC "Scout"
> A75 power, 72x36 Culver prop
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=480617#480617
>
>
>
>
>
>
>
>
>
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Turnbuckles =?ISO-8859-1?Q?ain=99t?= cheap |
Thanks everyone for your input. I guess I'm going to go for it. Suppose I'll let
everyone know how it turns out in a few years. I will be storing the wings uncovered
for a while as I build the fuselage. Maybe that'll give me a bit of a
preview of how things are going to shrink or stretch. I can always add the turnbuckles
before covering if it looks like things are sagging. A chance to save
over $200 is worth a try. By the way my crimper is the one from AS&S for $20.
--------
Dan O
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=480641#480641
Attachments:
http://forums.matronics.com//files/img_3515_143.jpg
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: ?Q?Re:_Pietenpol-List:_Turnbuckles_ain=99t_cheap? |
Dan I tried a crimper like you use and the threads stripped after a couple of crimps.
I like the looks of the single crimp.
Jack Textor
Sent from my iPad
> On Jun 4, 2018, at 3:40 PM, danoliver <danoliver909@gmail.com> wrote:
>
>
> Thanks everyone for your input. I guess I'm going to go for it. Suppose I'll
let everyone know how it turns out in a few years. I will be storing the wings
uncovered for a while as I build the fuselage. Maybe that'll give me a bit of
a preview of how things are going to shrink or stretch. I can always add the
turnbuckles before covering if it looks like things are sagging. A chance to
save over $200 is worth a try. By the way my crimper is the one from AS&S for
$20.
>
> --------
> Dan O
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=480641#480641
>
>
>
>
> Attachments:
>
> http://forums.matronics.com//files/img_3515_143.jpg
>
>
>
>
>
>
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | TIG Welding question |
Can you TIG weld 4130 steel using stainless steel rod? I use mild steel rods when
using OA to weld 4130 but don't know about TIG or using stainless steel rod
for 4130.
The reason I ask is my son has access to his company's TIG welder but for some
reason it is problematic to change the filler rod.
Thanks,
John Franklin
GN-1 / Corvair 164CID
Needville, TX
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|