Today's Message Index:
----------------------
1. 05:02 AM - Re: Continental front crank seal sealant (Archie)
2. 08:52 AM - Re: Continental front crank seal sealant (Randy L. Thwing)
3. 09:47 AM - Re: Continental front crank seal sealant (Jim Baker)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Continental front crank seal sealant |
--> Engines-List message posted by: "Archie" <archie97@earthlink.net>
Negative.
I have purchased it in 12 pack cans to save money.
(it is relatively expensive)
Since it goes a long way, I still have a few left.
Will try it next time.
====================================
----- Original Message -----
From: "Randy L. Thwing" <n4546v@mindspring.com>
Sent: Monday, April 10, 2006 10:50 PM
Subject: Re: Engines-List: Continental front crank seal sealant
> --> Engines-List message posted by: "Randy L. Thwing"
> <n4546v@mindspring.com>
>
> Hey Archie:
> Have you tried the new "racing formula", new and improved, Hylomar they
> describe on their website?
>
> Regards,
>
> Randy L. Thwing do not archive
>
>
> Subject: Re: Engines-List: Continental front crank seal sealant
>
>
>> --> Engines-List message posted by: "Archie" <archie97@earthlink.net>
>>
>> Finding Hylomar is no problem.
>> Most auto speed shops carry it inasmuch as engine builders
>> have been using it ever since Rolls licensed its manufacture.
>> I have used it on aircraft engines for over ten years.
>
>
>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Continental front crank seal sealant |
--> Engines-List message posted by: "Randy L. Thwing" <n4546v@mindspring.com>
Hey Jim:
Threebond makes a lot of products, is this the one? From their site:
"ThreeBond 1521 is an all-round adhesive whose main component is chloroprene
synthetic rubber. It is widely used not only for soft materials such as
rubber and leather, but also for hard materials such as metals."
Regards.
Randy
Subject: Re: Engines-List: Continental front crank seal sealant
> --> Engines-List message posted by: "Jim Baker" <jlbaker@msbit.net>
>
> > Pliobond works good.
>
> ThreeBond, as well.
>
> Jim Baker
> 580.788.2779
> Elmore City, OK
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Continental front crank seal sealant |
--> Engines-List message posted by: "Jim Baker" <jlbaker@msbit.net>
> Hey Jim:
> Threebond makes a lot of products, is this the one? From their
> site:
>
> "ThreeBond 1521 is an all-round adhesive whose main component
is
> chloroprene synthetic rubber. It is widely used not only for soft
> materials such as rubber and leather, but also for hard materials
such
> as metals."
Aiiieee....no! The 1521 is a contact cement.look for 1104 or 1211.
The 1104 is used on a lot of OEM assemblies from Japan to seal
crankcase halves.
http://www.threebond.co.jp/en/product/series/sealants/1100list.html
http://www.threebond.co.jp/en/product/number/index.html
I'd go with the 1104 if there aren't any large gaps. And I'd probably
not use any of the silicone based stuff. Knowing just how much of
the stuff extruded into the interior is always a worry and if any of it is
going to fall into the oil supply with deleterious effect. The 1104 is
pretty darn thin and is danged tough stuff. By no means the only
solution, just one among many tho.
Jim Baker
580.788.2779
Elmore City, OK
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|