Today's Message Index:
----------------------
1. 05:15 AM - Re: prop bolts (Gary Casey)
2. 07:56 AM - Re: Re: prop bolts (Noel Loveys)
3. 09:37 AM - Re: prop bolts (Gene Smith)
4. 09:49 AM - Re: prop bolts (Dale Fultz)
5. 10:40 AM - Re: prop bolts (Gene Smith)
6. 06:50 PM - Re: prop bolts (dj45)
7. 06:52 PM - Re: prop bolts (dj45)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
My instruction manual said 60-65 ft-lb, clean and dry. They put
emphasis on the threads being dry, not lubricated. If the threads
are lubricated the proper torque would be lower, but I don't know how
low. This was for an Aerocomposites prop on an IO-540, but I believe
the hubs and bolts are the same for all Lycomings with constant-speed
props.
Gary Casey
>>
>> Can anyone tell me what the tourque on prop bolts should be? IO360
>> w/ alum prop.
>>
>> Thanks
>>
>> Dan Stanton
>> 90% done 90% to go
>> 801, IO360
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
If you accidentally get some oil or grease in the threads you can wash it
out with a bit of MEK.
Noel
> -----Original Message-----
> From: owner-engines-list-server@matronics.com
> [mailto:owner-engines-list-server@matronics.com] On Behalf Of
> Gary Casey
> Sent: Saturday, July 28, 2007 9:44 AM
> To: engines-list@matronics.com
> Subject: Engines-List: Re: prop bolts
>
>
>
> My instruction manual said 60-65 ft-lb, clean and dry. They put
> emphasis on the threads being dry, not lubricated. If the threads
> are lubricated the proper torque would be lower, but I don't
> know how
> low. This was for an Aerocomposites prop on an IO-540, but I
> believe
> the hubs and bolts are the same for all Lycomings with
> constant-speed
> props.
>
> Gary Casey
>
> >>
> >> Can anyone tell me what the tourque on prop bolts should
> be? IO360
> >> w/ alum prop.
> >>
> >> Thanks
> >>
> >> Dan Stanton
> >> 90% done 90% to go
> >> 801, IO360
>
>
>
>
>
>
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Dan...........Contact Sensenich Prop. Mfg. Co., 14 Citation Ln., Lititz, Pa.
17543......719-569-0435......or email Engineer Dave Burkhart
daveb@sensenich.com They will be glad to answer your
questions.................CHEERS!!!!.....and good luck!
Gene Smith
RV-4 14yrs.
----- Original Message -----
From: "dj45" <dj45@modempool.com>
Sent: Friday, July 27, 2007 11:37 AM
Subject: Engines-List: prop bolts
>
> Can anyone tell me what the tourque on prop bolts should be? IO360 w/ alum
prop.
>
> Thanks
>
> --------
> Do not archive
>
> Dan Stanton
> 90% done 90% to go
> 801, IO360
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=125903#125903
>
>
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Gene,,The correct phone number is 717-569-0435
----- Original Message -----
From: "Gene Smith" <esmith6@satx.rr.com>
Sent: Saturday, July 28, 2007 12:36 PM
Subject: Re: Engines-List: prop bolts
>
> Dan...........Contact Sensenich Prop. Mfg. Co., 14 Citation Ln., Lititz,
> Pa.
> 17543......719-569-0435......or email Engineer Dave Burkhart
> daveb@sensenich.com They will be glad to answer your
> questions.................CHEERS!!!!.....and good luck!
>
> Gene Smith
> RV-4 14yrs.
>
>
> ----- Original Message -----
> From: "dj45" <dj45@modempool.com>
> To: <engines-list@matronics.com>
> Sent: Friday, July 27, 2007 11:37 AM
> Subject: Engines-List: prop bolts
>
>
>>
>> Can anyone tell me what the tourque on prop bolts should be? IO360 w/
>> alum
> prop.
>>
>> Thanks
>>
>> --------
>> Do not archive
>>
>> Dan Stanton
>> 90% done 90% to go
>> 801, IO360
>>
>>
>>
>>
>> Read this topic online here:
>>
>> http://forums.matronics.com/viewtopic.php?p=125903#125903
>>
>>
>>
>>
>>
>>
>>
>>
>>
>
>
>
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Dale, you are correct, and thanks.........Dan, sorry, hope that little digit
didn't screw your plans up too much...I don't think they are open on
Saturdays any way?.........CHEERS!!!!
Please do not ARCHIVE!
----- Original Message -----
From: "Dale Fultz" <dfultz7@earthlink.net>
Sent: Saturday, July 28, 2007 11:47 AM
Subject: Re: Engines-List: prop bolts
>
> Gene,,The correct phone number is 717-569-0435
> ----- Original Message -----
> From: "Gene Smith" <esmith6@satx.rr.com>
> To: <engines-list@matronics.com>
> Sent: Saturday, July 28, 2007 12:36 PM
> Subject: Re: Engines-List: prop bolts
>
>
> >
> > Dan...........Contact Sensenich Prop. Mfg. Co., 14 Citation Ln., Lititz,
> > Pa.
> > 17543......719-569-0435......or email Engineer Dave Burkhart
> > daveb@sensenich.com They will be glad to answer your
> > questions.................CHEERS!!!!.....and good luck!
> >
> > Gene Smith
> > RV-4 14yrs.
> >
> >
> > ----- Original Message -----
> > From: "dj45" <dj45@modempool.com>
> > To: <engines-list@matronics.com>
> > Sent: Friday, July 27, 2007 11:37 AM
> > Subject: Engines-List: prop bolts
> >
> >
> >>
> >> Can anyone tell me what the tourque on prop bolts should be? IO360 w/
> >> alum
> > prop.
> >>
> >> Thanks
> >>
> >> --------
> >> Do not archive
> >>
> >> Dan Stanton
> >> 90% done 90% to go
> >> 801, IO360
> >>
> >>
> >>
> >>
> >> Read this topic online here:
> >>
> >> http://forums.matronics.com/viewtopic.php?p=125903#125903
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >
> >
> >
> >
> >
> >
>
>
Message 6
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Thank you every one. I think I have a handle on it now.
--------
Do not archive
Dan Stanton
95% done paint to go
801, IO360
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=126087#126087
Message 7
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
You know, sometimes these planes start to get complacated. Way too many details
to keep track of for an old man.
--------
Do not archive
Dan Stanton
95% done paint to go
801, IO360
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=126088#126088
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|