Europa-List Digest Archive

Sun 09/21/03


Total Messages Posted: 4



Today's Message Index:
----------------------
 
     1. 01:27 PM - 914 Fuel Flow (Jim Butcher)
     2. 02:28 PM - Re: 1st Stupid Question (Fergus Kyle)
     3. 05:00 PM - Re: Fuel flow measurement for 914 (Tony S. Krzyzewski)
     4. 09:40 PM - [Please Read] SPAM Filter Could Be Causing Posting Problems (Matt Dralle)
 
 
 


Message 1


  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 01:27:30 PM PST US
    From: "Jim Butcher" <europa@triton.net>
    Subject: 914 Fuel Flow
    --> Europa-List message posted by: "Jim Butcher" <europa@triton.net> We're trying to purchase the proper fuel flow transducers. Does anyone know what the flow to and the flow from the engine for a 914 is? I've heard as much as 60 liters/hour. Thanks Jim & Heather A185


    Message 2


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 02:28:56 PM PST US
    From: "Fergus Kyle" <VE3LVO@rac.ca>
    Subject: Re: 1st Stupid Question
    --> Europa-List message posted by: "Fergus Kyle" <VE3LVO@rac.ca> ----- Original Message ----- From: <TELEDYNMCS@aol.com> Subject: Re: Europa-List: 1st Stupid Question | --> Europa-List message posted by: TELEDYNMCS@aol.com | | In a message dated 9/12/2003 12:14:17 PM Eastern Daylight Time, | RobH@hyperion-ef.com writes: | | > What's the denatured alcohol for? | > | | Cleaning up sissors and squeegees after using them on wet epoxy. Vinegar | works too, especially if you happen to get resin on bare skin. | | Regards, | | John Lawton | Dunlap, TN | A-245 Cheers, I use cider vinegar for tools. Cheaper (cheeper) Ferg


    Message 3


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 05:00:11 PM PST US
    Subject: Fuel flow measurement for 914
    From: "Tony S. Krzyzewski" <tonyk@kaon.co.nz>
    --> Europa-List message posted by: "Tony S. Krzyzewski" <tonyk@kaon.co.nz> I think what you're looking for is a return flow controller. Here's a cool one... :-) http://www.matronics.com/fuelchec/RFC/index.html ... And it works very well... We've got one in ZK-UBD. Tony


    Message 4


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 09:40:23 PM PST US
    From: Matt Dralle <dralle@matronics.com>
    Subject: [Please Read] SPAM Filter Could Be Causing Posting Problems
    For Some Members...? --> Europa-List message posted by: Matt Dralle <dralle@matronics.com> Dear Listers, Matronics is now utilizing a SPAM filter appliance to filter out the excessive amounts of inappropriate email that bombards the Email List Forums each day. The filter is reporting that over 66% of the email messages sent to Matronics email destinations are of SPAM content and reviewing the logfiles, it would appear to be true. That is indeed great! While the Lists are enjoying the breath of fresh air afforded by the new appliance, I am suspecting that a few legitimate email List posts are being blocked as too, although I can't confirm this. It is difficult to churn through the logfiles looking though thousands of blocked email messages trying to determine if any legitimate List posts were blocked. If you suspect that your posts are accidently being blocked by the SPAM filter appliance, I have created a new Trouble Report web page that will allow you to report your problems directly to me without having to use email. If the SPAM filter is blocking your email address for some reason, then its likely that I wouldn't be able to receive your direct email regarding difficulty in posting. The web form bypasses the incoming email and directs your message directly to me. Please include as much information as possible regarding the problems you are having including any bounced email or email error messages that you may have received back in regard to your posts to the lists. The more information I have about the email you are sending and what the errors you are receiving, the better chance I'll have in hunting down the problem. The Trouble Report Website URL is: http://www.matronics.com/trouble-report/ I apologize for any inconvenience the SPAM filter may be causing you. I will work toward resolving your issues as quickly as possible. Best regards, Matt Dralle Matronics EMail List Administrator Matt G Dralle | Matronics | PO Box 347 | Livermore | CA | 94551 925-606-1001 V | 925-606-6281 F | dralle@matronics.com Email http://www.matronics.com/ WWW | Featuring Products For Aircraft




    Other Matronics Email List Services

  • Post A New Message
  •   europa-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/Europa-List.htm
  • Full Archive Search Engine
  •   http://www.matronics.com/search
  • 7-Day List Browse
  •   http://www.matronics.com/browse/europa-list
  • Browse Europa-List Digests
  •   http://www.matronics.com/digest/europa-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contributions

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --