Today's Message Index:
----------------------
1. 04:36 AM - Re: Bing 64 Carb and Altitude Compensation (Miles McCallum)
2. 08:06 AM - Address change (DJA727@aol.com)
3. 11:37 AM - 'bid, anybody know offhand what..... (TELEDYNMCS@aol.com)
4. 12:39 PM - Matronics Internet Connection Repaired!! (Matt Dralle)
5. 12:55 PM - Tachometer connection for 914 to EIS (Paul McAllister)
6. 06:36 PM - Re: 'bid, anybody know offhand what..... (Cliff Shaw)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Bing 64 Carb and Altitude Compensation |
--> Europa-List message posted by: "Miles McCallum" <milesm@avnet.co.uk>
> > Of course, the answer is fuel injection - there's a perfect bit of kit
out
> > there, made by Weber, as used on Ducati m/cs etc - fully programmable
(but
> > you need the bit of kit and software to do it) see:
> > http://www.fuelinmoto.com.au/
> >
> > Miles
> >
> >
> Has anyone ever fitted fuel injection to a Rotax?
>
> Jeff
Not that I know of - but our Rotax agent has the kit, but not had the time
to fit it and dial it in.
M
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> Europa-List message posted by: DJA727@aol.com
Hello Fellow Europa builders!
For those who would wish to contact me, I am changing my email address. This
one will be inop as soon as I can get this squared away with the new one. The
new one is:
dja767@charter.net
We are entering the high speed age!
Cheers,
Dave Anderson
A227
Mini U2
137 hours and counting
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | 'bid, anybody know offhand what..... |
--> Europa-List message posted by: TELEDYNMCS@aol.com
Greetings,
Does anybody know the weight of the 'bid supplied with the kit? I've looked
all over the manual and it doesn't specify. I'm almost out and I need to order
some more, along with a few other things from ACS.
Thanks!
Regards,
John Lawton
Dunlap, TN
A-245 (Today: Vacuum bagging baggage bay supports and final installation and
glassing of the tie bar)
Completed so far:
Wings - closed, incidence set, ailerons, flaps and wings ready to start
finish process.
Fuselage - CM installed, TP torque tube, mass balance and trim installed.
Flap actuator installed. Landing gear installed. Overhead console and conduit
finished. Center console cut-a-way complete.
Panel - Flight instruments mounted, then removed and ready for paint
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Matronics Internet Connection Repaired!! |
--> Europa-List message posted by: Matt Dralle <dralle@matronics.com>
Dear Listers,
The phone company was out here bright and early this morning and repaired
the wires and the T1 connection is back up and rock solid!
Again my apologies for any inconvenience the disruption may have caused.
Best regards,
Matt Dralle
Matronics Email List Admin.
Matt G Dralle | Matronics | PO Box 347 | Livermore | CA | 94551
925-606-1001 V | 925-606-6281 F | dralle@matronics.com Email
http://www.matronics.com/ WWW | Featuring Products For Aircraft
do not archive
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Tachometer connection for 914 to EIS |
--> Europa-List message posted by: "Paul McAllister" <paul.mcallister@qia.net>
Hi all,
I was wondering if someone out there who has connected an EIS to a 914 can help
with the tachometer connection. The Grand Rapids manual show a generic 912/914
connection, however when looking in the 914 installation manual it shows two
wires from the TCU for the tachometer. Is this what is used for the EIS or
is it done differently. ?
Thanks, Paul
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: 'bid, anybody know offhand what..... |
--> Europa-List message posted by: "Cliff Shaw" <flyinggpa@comcast.net>
John
The glass is a little bit different than regular glass. It is a "skip"
weave. I did not fine it in the ACS catalog. Call John at Lakeland, I
thing he has it for sale.
Cliff Shaw
1041 Euclid ave.
Edmonds WA 98020
(425) 776-5555
N229WC "Wile E Coyote"
New Email:" flyinggpa@comcast.net "
----- Original Message -----
From: <TELEDYNMCS@aol.com>
Subject: Europa-List: 'bid, anybody know offhand what.....
> --> Europa-List message posted by: TELEDYNMCS@aol.com
>
> Greetings,
>
> Does anybody know the weight of the 'bid supplied with the kit? I've
looked
> all over the manual and it doesn't specify. I'm almost out and I need to
order
> some more, along with a few other things from ACS.
>
> Thanks!
>
> Regards,
>
> John Lawton
> Dunlap, TN
> A-245 (Today: Vacuum bagging baggage bay supports and final installation
and
> glassing of the tie bar)
>
> Completed so far:
>
> Wings - closed, incidence set, ailerons, flaps and wings ready to start
> finish process.
> Fuselage - CM installed, TP torque tube, mass balance and trim installed.
> Flap actuator installed. Landing gear installed. Overhead console and
conduit
> finished. Center console cut-a-way complete.
> Panel - Flight instruments mounted, then removed and ready for paint
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|