Today's Message Index:
----------------------
1. 01:40 AM - Floscan (Graham Singleton)
2. 05:16 AM - Re: Where to buy a Floscan (nigel charles)
3. 10:00 AM - earthing (Paul Stewart)
4. 10:34 AM - Re: earthing (R.C.Harrison)
5. 11:14 AM - Re: earthing (Gerry Holland)
6. 12:05 PM - Re: Drop of a Hat Fly-ins (William Mills)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
--> Europa-List message posted by: Graham Singleton <graham@gflight.f9.co.uk>
At 23:56 19/02/2004 -0800, you wrote:
>Tony,
>Rocky Mountain Instruments has them. Check with John Wigney on how to get
>away with using only one even with the return fuel line installed.
>
>Troy Maynor
Tony
Grand Rapids sells them too.
Graham
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Where to buy a Floscan |
--> Europa-List message posted by: "nigel charles" <nigelcharles@tiscali.co.uk>
You can deal with Floscan direct in Seattle. I went to their offices at:
3016 NE Blakely Street
Seattle
WA 98105
Tel: 001 206 524 6625
This info is about 5 years old so it may be out of date.
Nigel Charles
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
--> Europa-List message posted by: Paul Stewart <europa@pstewart.f2s.com>
Sounds like a stupid question but how do I go about attaching the shield
of shielded wire (mags) to ground - I'm thinking a metal cable clamp
over the braid connected to ground or does one stuff the braid into a
crip terminal?
Regards
Paul Stewart #432 G-GIDY
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
--> Europa-List message posted by: "R.C.Harrison" <ptag.dev@ukonline.co.uk>
Hi! Paul
If you carefully pull a hole in the braid cover with a pointed tool (without
stabbing the insulation below) you can then pull a loop of the centre core,
including it's isulation, through the hole. This now leaves you with a "tail
" of the shield to make a connection to to take to the common ground you
have for other ground connections.
In my case it is advised to only ground one end and that is to the engine.
BTW It's not a stupid question just a "wrinkle" that you collect on the
route of life's rich tapestry, never be afraid to ask.
Regards
Bob Harrison G-PTAG Europa MKI/Jabiru 3300.
----- Original Message -----
From: "Paul Stewart" <europa@pstewart.f2s.com>
Subject: Europa-List: earthing
> --> Europa-List message posted by: Paul Stewart <europa@pstewart.f2s.com>
>
> Sounds like a stupid question but how do I go about attaching the shield
> of shielded wire (mags) to ground - I'm thinking a metal cable clamp
> over the braid connected to ground or does one stuff the braid into a
> crip terminal?
>
> Regards
>
> Paul Stewart #432 G-GIDY
>
>
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
--> Europa-List message posted by: Gerry Holland <gnholland@onetel.com>
Paul Hi!
I'm thinking a metal cable clamp over the braid connected to ground or does
one stuff the braid into a crimp terminal?
Use Crimp and ensure Earth wire =8Cman=B9 enough. RS Components do various
Earthing Straps in Braded with Terminals.
12=B2 and 18=B2
Regards
Gerry
Europa 384 G-FIZY
Trigear with 912 and Arplast CS Prop.
Fuselage being Painted, Wings ready to paint, Flying surfaces painted
Airframe Wiring complete, Full Size Panel 60% done .
Includes Dynon EFIS, KMD 150, Icom A-200 and SL70 Transponder. AoA Fitted.
Activity on Panel completion, Heater Unit, Shoulder Width Mod.
http://www.g-fizy.com
+44 7808 402404
gnholland@onetel.com
Message 6
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Drop of a Hat Fly-ins |
--> Europa-List message posted by: "William Mills" <combined.merchants@virgin.net>
Lighter winds tomorrow (Saturday) so I suggest Fenland for noon. Hope one
or two others can make it - only two at Old Sarum - Rick Morris and me, plus
Brian Tarmar who is still building. Very enjoyable company and a nice
lunch.
Best wishes,
William
(Do not archive)
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|