Today's Message Index:
----------------------
 
     1. 01:38 PM - Re: Rudder cables look very close to the fuel tank fittings (Tony Krzyzewski)
     2. 10:23 PM - Re: Rudder cables look very close to the fuel tank fittings (josok)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
01:38:09 PM PST US
Subject: 
Rudder cables look very close to the fuel tank fittings
From: 
"Tony Krzyzewski" <tonyk@kaon.co.nz>
      Received-SPF: none
      
      --> Europa-List message posted by: "Tony Krzyzewski" <tonyk@kaon.co.nz>
      
      >> The rudder cable runs seem VERY close to
      the fuel tank fittings and I was wondering if anyone else had had this, or
      is there some way of ensuring they dont contact?
      
      Jeremy,
      
      Run them in nylaflow tube alongside the tank and the pitchstop support using small
      brackets to hold the nylaflow in place. If you also use nylaflow tubes through
      the fin out to the tailwheel rather than stainless steel then you'll find
      the tubes will deflect as the tailwheel moves and reduce friction wear of the
      cables at that point.
      
      
      Regards
      
      tony
      
      
      
      
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
10:23:22 PM PST US
Subject: 
RE: Rudder cables look very close to the fuel tank fittings
From: 
"josok" <josok-e@ukolo.fi>
              2.60 REPLY_TO_EMPTY         Reply-To: is empty
      
      --> Europa-List message posted by: "josok" <josok-e@ukolo.fi>
      
      My tank did not end up exactly in the middle. The result was, that the starboard
      rudder cable was touching the tank. I decided against the tubing option because
      i fear water collecting in the tube. Freezing water will cause a stuck rudder
      consequently. So i added a second pulley wheel at the end of the tunnel in
      the cockpit module, which also does the job. 
      
      Cu,
      
      Jos Okhuijsen
      ----------------
      Visit EuropaOwnersForum http://www.europaowners.org/
      
      
      
      
      
      








Other Matronics Email List Services




Post A New Message
  
europa-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/Europa-List.htm
Full Archive Search Engine
  
http://www.matronics.com/search
7-Day List Browse
  
http://www.matronics.com/browse/europa-list
Browse Europa-List Digests
  
http://www.matronics.com/digest/europa-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contributions









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --