---------------------------------------------------------- Europa-List Digest Archive --- Total Messages Posted Sun 02/19/06: 4 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 07:38 AM - Check valve dimensions (Fergus Kyle) 2. 09:25 AM - Re: Check valve dimensions (ivor.phillips) 3. 09:58 AM - Re: Check valve dimensions (G-IANI) 4. 12:36 PM - Fuel Gauge New Release (Tony Krzyzewski) ________________________________ Message 1 _____________________________________ Time: 07:38:58 AM PST US From: "Fergus Kyle" Subject: Europa-List: Check valve dimensions --> Europa-List message posted by: "Fergus Kyle" Cheers, I am planning the "fuel pump board" for the rear baggage area and it will be about 13-1/2"x9-1/2" and vertical. When I received my FWF kit, it appeasr the company was in its agony throes and I didn't notice some lacking parts, among which were the NRV (check valves) which are spec'd in parallel with now-series pumps. Roger is very kindly sending these, but in the interim, I want to plan the layout. If your magic carpet is nearby, and you think of it, I would very much appreciate a measurement of the overall length of your Europa-issue check valves and/or the approximate length of the 'body' OAL minus nipples. I presume the nipples to be 3/4" or 19mm each for 8mm tubing. Thank you in advance, Ferg A064 engine hung ________________________________ Message 2 _____________________________________ Time: 09:25:40 AM PST US From: "ivor.phillips" Subject: Re: Europa-List: Check valve dimensions --> Europa-List message posted by: "ivor.phillips" Hi Ferg Assuming that Europa give you the Andair CK321-H check valve, The measurements are 72.80mm overall including nipples, Body only is 41.40mm, the nipples are 8.20mm O/D, Diameter for the main body are 27.40mm Ivor Phillips ----- Original Message ----- From: "Fergus Kyle" Sent: Sunday, February 19, 2006 3:33 PM Subject: Europa-List: Check valve dimensions > --> Europa-List message posted by: "Fergus Kyle" > > Cheers, > I am planning the "fuel pump board" for the rear baggage area > and it will be about 13-1/2"x9-1/2" and vertical. When I received my FWF > kit, it appeasr the company was in its agony throes and I didn't notice > some > lacking parts, among which were the NRV (check valves) which are spec'd in > parallel with now-series pumps. Roger is very kindly sending these, but in > the interim, I want to plan the layout. > If your magic carpet is nearby, and you think of it, I would > very much appreciate a measurement of the overall length of your > Europa-issue check valves and/or the approximate length of the 'body' OAL > minus nipples. I presume the nipples to be 3/4" or 19mm each for 8mm ________________________________ Message 3 _____________________________________ Time: 09:58:58 AM PST US From: "G-IANI" Subject: RE: Europa-List: Check valve dimensions --> Europa-List message posted by: "G-IANI" Ferg The Andair check valves are 44.5mm between the ends of the pipe (when pushed fully home) I will send you direct a picture of the layout I used for Terry Clark G-IRON if this helps Ian Rickard #505 G-IANI XS Trigear Europa Club Mods Rep (Trigear) e-mail mods@europaclub.org.uk or direct g-iani@ntlworld.com -----Original Message----- From: owner-europa-list-server@matronics.com [mailto:owner-europa-list-server@matronics.com]On Behalf Of Fergus Kyle Sent: 19 February 2006 15:33 Subject: Europa-List: Check valve dimensions --> Europa-List message posted by: "Fergus Kyle" Cheers, I am planning the "fuel pump board" for the rear baggage area and it will be about 13-1/2"x9-1/2" and vertical. When I received my FWF kit, it appeasr the company was in its agony throes and I didn't notice some lacking parts, among which were the NRV (check valves) which are spec'd in parallel with now-series pumps. Roger is very kindly sending these, but in the interim, I want to plan the layout. If your magic carpet is nearby, and you think of it, I would very much appreciate a measurement of the overall length of your Europa-issue check valves and/or the approximate length of the 'body' OAL minus nipples. I presume the nipples to be 3/4" or 19mm each for 8mm tubing. Thank you in advance, Ferg A064 engine hung ________________________________ Message 4 _____________________________________ Time: 12:36:14 PM PST US Subject: Europa-List: Fuel Gauge New Release From: "Tony Krzyzewski" --> Europa-List message posted by: "Tony Krzyzewski" I have now completed the design and testing of the new version fuel gauge which can now operate either as a standalone fuel gauge and display or as an input into the Dynon EMS system. Construction details can be found at http://www.kaon.co.nz/europa/fuelgaugev5.pdf For those who have been patiently waiting for their chips since Crhistmas I'll be posting them out today. Apologies for the delay but I really wanted to get this new code finished and tested before sending them out. Regards Tony