---------------------------------------------------------- Europa-List Digest Archive --- Total Messages Posted Fri 09/29/06: 5 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 09:41 AM - transducers (danny@mcwalterscafe.co.uk) 2. 10:38 AM - Re: transducers (Peter Rees) 3. 02:02 PM - Re: transducers (steve v) 4. 04:02 PM - Re: transducers (Peter Rees) 5. 10:56 PM - Monowheel sight gauge () ________________________________ Message 1 _____________________________________ Time: 09:41:32 AM PST US From: "danny@mcwalterscafe.co.uk" Subject: Europa-List: transducers --> Europa-List message posted by: "danny@mcwalterscafe.co.uk" Hi Folks, I'm just about ready to fit the transducers for the fuel meter, I presume the best place for them would be in the tunnel. also if fitted in the tunnel would I still have to use the fire sleeve provided? shouldn't think it would be that hot in there (I hope !!!). Rgd Danny G-c.e.r.i First engine start in the next two weeks!!!! nervous me...nah ________________________________ Message 2 _____________________________________ Time: 10:38:07 AM PST US From: "Peter Rees" Subject: Re: Europa-List: transducers --> Europa-List message posted by: "Peter Rees" On a very similar subject - I'd like to fit one of the MGL fuel pressure gauges - they recommend a VDO transducer with a 'fuel isolator' (which I assume prevents the fuel from escaping in the event that the diaphragm in the transducer fails). Can I ask what transducers others have fitted for fuel pressure and if they've found it necessary to use an isolator? If anyone has any experiences of the MGL range, that would be appreciated too. Thanks Peter ________________________________ Message 3 _____________________________________ Time: 02:02:59 PM PST US Subject: Re: Europa-List: transducers From: "steve v " --> Europa-List message posted by: "steve v " Hi Peter, if you are in the UK the PFA will not approve the MGL fuel flow transducer- i have a brand new unused one which is now an expensive mantle piece ornament ! they did approve the Floscan Fuel Flow Transducer. hope this info is of some use, steve vestuti #573 -------------------- m2f -------------------- Visit - www.EuropaOwners.org http://www.europaowners.org/viewtopic.php?p=12823#12823 -------------------- m2f -------------------- ________________________________ Message 4 _____________________________________ Time: 04:02:29 PM PST US From: "Peter Rees" Subject: Re: Europa-List: transducers --> Europa-List message posted by: "Peter Rees" thanks for this steve - was really looking at the pressure transducer (VDO) but it goes on about a fuel isolator. Do you have the MGL fuel computer? If so, is it a good bit of kit? I guess you need two flowscans - one for the feed and one for the return? ----- Original Message ----- From: "steve v " Sent: Friday, September 29, 2006 10:01 PM Subject: Re: Europa-List: transducers > --> Europa-List message posted by: "steve v " > > Hi Peter, if you are in the UK the PFA will not approve the MGL fuel flow > transducer- i have a brand new unused one which is now an expensive > mantle piece ornament ! they did approve the Floscan Fuel Flow Transducer. > hope this info is of some use, > > steve vestuti #573 > > > -------------------- m2f -------------------- > > Visit - www.EuropaOwners.org > http://www.europaowners.org/viewtopic.php?p=12823#12823 > > -------------------- m2f -------------------- > > > ________________________________ Message 5 _____________________________________ Time: 10:56:03 PM PST US Subject: Europa-List: Monowheel sight gauge From: --> Europa-List message posted by: What is your favorite location for Sight Gauge on a Monowheel? How and where did you route vent? Ron Parigoris I have a factory float style gauge, also water drains where I could Tee off port drain to sight gauge?