Today's Message Index:
----------------------
1. 01:38 AM - DOTH Friday 15th Sleap (Paddy Clarke)
2. 10:44 AM - Monowheel trailer for sale (R Holder)
3. 01:49 PM - control bearing installation (Rowland Carson)
4. 03:30 PM - FW: Fuel Transfer pumps (Alan Burrows)
5. 06:12 PM - Re: control bearing installation (Rick Stockton)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | DOTH Friday 15th Sleap |
Hi Folks,
It seems we may have a short break in the weather tomorrow (Friday),
so how about a DOTH. As has been mentioned before, there seem to be
no suitable places with freebies - so , if no one has any better
ideas, I suggest Sleap. 1200ish as usual.
All the best, Paddy
Paddy Clarke
Europa G-KIMM
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Monowheel trailer for sale |
UK (and Europe) Europa people
I have a factory monowheel trailer for sale.
Details from me, I will listen to offers !
Richard Holder
G-OWWW High Cross
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | control bearing installation |
I am nearly ready to install the SRBF (Tufnol) bearings for the main
roll torque tubes.
For the forward bearing CS04, the words on page 13-6 and the exploded
fastener diagram on page 13-12 do not show a washer between the bolt
head and the Tufnol. Only the large washer on the glass-fibre side of
the assembly is mentioned. But the assembled bolt shown in the other
hole of CS04 does appear to have a washer under its head.
However, the words on page 13-6 and the diagram on page 13-13 for the
aft bearing CS06 both show AN960-10L washers between the nuts and the
Tufnol.
Fitting the washers on the forward bearing fasteners would make the
installation consistent with that for the aft bearings. Does anyone
think I'd be wrong to fit the AN960-10L washers under the front
bearing bolt heads, or is there a good reason for them to be omitted?
BTW, my inventory shows that if I don't fit them, I actually have 4
washers surplus in the fuselage kit; if I do fit them I am 4 short!
regards
Rowland
--
| Rowland Carson LAA #16532 http://home.clara.net/rowil/aviation/
| 1070 hours building Europa #435 G-ROWI e-mail <rowil@clara.net>
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | FW: Fuel Transfer pumps |
Hi Everyone
I have finally received a new supply of these pumps from the manufacturers.
If anyone wants one please contact me offline at alan@alan-burrows.com
To everyone who has already ordered you should receive it within the next
few days as they will be posted out tomorrow and sorry for the delay.
Alan
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: control bearing installation |
Rowland, for what it is worth. I followed the manual and did not install the washers
AN960-10L under the bolt on the front Tufnol bearing. I did install them
on the back Tufnol bearing. Take a look at page 13-12 and page 13-13 issue
3.
Rick Stockton
A210
Rowland Carson <rowil@clara.net> wrote:
I am nearly ready to install the SRBF (Tufnol) bearings for the main
roll torque tubes.
For the forward bearing CS04, the words on page 13-6 and the exploded
fastener diagram on page 13-12 do not show a washer between the bolt
head and the Tufnol. Only the large washer on the glass-fibre side of
the assembly is mentioned. But the assembled bolt shown in the other
hole of CS04 does appear to have a washer under its head.
However, the words on page 13-6 and the diagram on page 13-13 for the
aft bearing CS06 both show AN960-10L washers between the nuts and the
Tufnol.
Fitting the washers on the forward bearing fasteners would make the
installation consistent with that for the aft bearings. Does anyone
think I'd be wrong to fit the AN960-10L washers under the front
bearing bolt heads, or is there a good reason for them to be omitted?
BTW, my inventory shows that if I don't fit them, I actually have 4
washers surplus in the fuselage kit; if I do fit them I am 4 short!
regards
Rowland
--
| Rowland Carson LAA #16532 http://home.clara.net/rowil/aviation/
| 1070 hours building Europa #435 G-ROWI e-mail
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|