---------------------------------------------------------- Europa-List Digest Archive --- Total Messages Posted Thu 08/14/08: 5 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 01:38 AM - DOTH Friday 15th Sleap (Paddy Clarke) 2. 10:44 AM - Monowheel trailer for sale (R Holder) 3. 01:49 PM - control bearing installation (Rowland Carson) 4. 03:30 PM - FW: Fuel Transfer pumps (Alan Burrows) 5. 06:12 PM - Re: control bearing installation (Rick Stockton) ________________________________ Message 1 _____________________________________ Time: 01:38:53 AM PST US From: Paddy Clarke Subject: Europa-List: DOTH Friday 15th Sleap Hi Folks, It seems we may have a short break in the weather tomorrow (Friday), so how about a DOTH. As has been mentioned before, there seem to be no suitable places with freebies - so , if no one has any better ideas, I suggest Sleap. 1200ish as usual. All the best, Paddy Paddy Clarke Europa G-KIMM ________________________________ Message 2 _____________________________________ Time: 10:44:39 AM PST US From: R Holder Subject: Europa-List: Monowheel trailer for sale UK (and Europe) Europa people I have a factory monowheel trailer for sale. Details from me, I will listen to offers ! Richard Holder G-OWWW High Cross ________________________________ Message 3 _____________________________________ Time: 01:49:19 PM PST US From: Rowland Carson Subject: Europa-List: control bearing installation I am nearly ready to install the SRBF (Tufnol) bearings for the main roll torque tubes. For the forward bearing CS04, the words on page 13-6 and the exploded fastener diagram on page 13-12 do not show a washer between the bolt head and the Tufnol. Only the large washer on the glass-fibre side of the assembly is mentioned. But the assembled bolt shown in the other hole of CS04 does appear to have a washer under its head. However, the words on page 13-6 and the diagram on page 13-13 for the aft bearing CS06 both show AN960-10L washers between the nuts and the Tufnol. Fitting the washers on the forward bearing fasteners would make the installation consistent with that for the aft bearings. Does anyone think I'd be wrong to fit the AN960-10L washers under the front bearing bolt heads, or is there a good reason for them to be omitted? BTW, my inventory shows that if I don't fit them, I actually have 4 washers surplus in the fuselage kit; if I do fit them I am 4 short! regards Rowland -- | Rowland Carson LAA #16532 http://home.clara.net/rowil/aviation/ | 1070 hours building Europa #435 G-ROWI e-mail ________________________________ Message 4 _____________________________________ Time: 03:30:09 PM PST US From: "Alan Burrows" Subject: Europa-List: FW: Fuel Transfer pumps Hi Everyone I have finally received a new supply of these pumps from the manufacturers. If anyone wants one please contact me offline at alan@alan-burrows.com To everyone who has already ordered you should receive it within the next few days as they will be posted out tomorrow and sorry for the delay. Alan ________________________________ Message 5 _____________________________________ Time: 06:12:00 PM PST US From: Rick Stockton Subject: Re: Europa-List: control bearing installation Rowland, for what it is worth. I followed the manual and did not install the washers AN960-10L under the bolt on the front Tufnol bearing. I did install them on the back Tufnol bearing. Take a look at page 13-12 and page 13-13 issue 3. Rick Stockton A210 Rowland Carson wrote: I am nearly ready to install the SRBF (Tufnol) bearings for the main roll torque tubes. For the forward bearing CS04, the words on page 13-6 and the exploded fastener diagram on page 13-12 do not show a washer between the bolt head and the Tufnol. Only the large washer on the glass-fibre side of the assembly is mentioned. But the assembled bolt shown in the other hole of CS04 does appear to have a washer under its head. However, the words on page 13-6 and the diagram on page 13-13 for the aft bearing CS06 both show AN960-10L washers between the nuts and the Tufnol. Fitting the washers on the forward bearing fasteners would make the installation consistent with that for the aft bearings. Does anyone think I'd be wrong to fit the AN960-10L washers under the front bearing bolt heads, or is there a good reason for them to be omitted? BTW, my inventory shows that if I don't fit them, I actually have 4 washers surplus in the fuselage kit; if I do fit them I am 4 short! regards Rowland -- | Rowland Carson LAA #16532 http://home.clara.net/rowil/aviation/ | 1070 hours building Europa #435 G-ROWI e-mail ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message europa-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Europa-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/europa-list Browse Digests http://www.matronics.com/digest/europa-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.