Europa-List Digest Archive

Wed 10/20/10


Total Messages Posted: 6



Today's Message Index:
----------------------
 
     1. 03:16 AM - Thanks (Paddy Clarke)
     2. 10:14 AM - Re: Re: Singleton firewall (William Daniell)
     3. 10:24 AM - Re: Singleton firewall (graeme bird)
     4. 10:32 AM - Re: Singleton firewall (Troy Maynor)
     5. 10:52 AM - Re: Re: Singleton firewall (Gerry Holland)
     6. 11:38 AM - Re: Re: Singleton firewall (GRAHAM SINGLETON)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 03:16:22 AM PST US
    From: Paddy Clarke <paddyclarke@lineone.net>
    Subject: Thanks
    Many thanks to all who responded to my queries, All the best, Paddy Paddy Clarke Europa G-KIMM


    Message 2


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 10:14:50 AM PST US
    From: William Daniell <wdaniell@etb.net.co>
    Subject: Re: Singleton firewall
    Yup sure is thanks Will On 19-Oct-10 20:56, Troy Maynor wrote: > --> Europa-List message posted by: "Troy Maynor"<wingnut54@charter.net> > > Hi Bill, > Perhaps these pix on the gallery link might help. I put sheet silicone, held with little stainless strips, around the holes cut for the engine mount. This provides a good seal around the tubes. There was a good deal of trimming with a dremel to get a good fit. I was going to use fire caulk around the seams but ended up putting insulation over the whole thing anyway so I ommited the sealant. Hope this helps. > Troy Maynor > > > http://www.europaowners.org/forums/gallery2.php?g2_itemId=44024 > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=316406#316406 > > > . >


    Message 3


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 10:24:36 AM PST US
    Subject: Re: Singleton firewall
    From: "graeme bird" <graeme@gdbmk.co.uk>
    I am now confused about the firewall, can I ask, is this for the tri-gear only, is it in addition to the Stainless firewall or instead of? Is it quicker or better? Some people seem to have used adhesive backed foil sheet over the whole area including surround. And the FWFD kit includes a quantity of firewall fabric, what is that used for. I have ordered the engine and fwfd kit and just getting ready for them, I have the shiny firewall plates done. Regards Graeme -------- Graeme Bird Read this topic online here: http://forums.matronics.com/viewtopic.php?p=316476#316476


    Message 4


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 10:32:52 AM PST US
    Subject: Re: Singleton firewall
    From: "Troy Maynor" <wingnut54@charter.net>
    I can't say if it works on the trigear or not. I don't see why not. I think it was designed for both but not sure. It is an alternative to making the stainless one. At first I thought it unuseable but I got to sanding and filing and am very pleased with the results. It is easily removeable after you remove the engine mount. Troy Maynor Read this topic online here: http://forums.matronics.com/viewtopic.php?p=316477#316477


    Message 5


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 10:52:55 AM PST US
    Subject: Re: Singleton firewall
    From: Gerry Holland <gholland@content-stream.co.uk>
    The Graham Singleton Firewall fits the XS Trigear. It did for mine anyway. Regards Gerry Do not archive


    Message 6


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 11:38:34 AM PST US
    From: GRAHAM SINGLETON <grahamsingleton@btinternet.com>
    Subject: Re: Singleton firewall
    Graeme=0Ait was designed for both mono and tri gear. Advantage was that all of the holes =0Acould be sealed which is almost impossible with the stainl ess one. It also =0Aoffers a less draggy space for fast moving colling air to get out of the =0Acowling. Cooling drag is a very significant part of to tal drag with an efficient =0Aairframe like the Europa. Holes are particula rly bad, lot of drag plus they =0Aallow flames to get through.=0AUnfortunat ely I can't make them now. =0AGraham=0A=0A=0A=0A=0A________________________ ________=0AFrom: graeme bird <graeme@gdbmk.co.uk>=0ATo: europa-list@matroni cs.com=0ASent: Wednesday, 20 October, 2010 18:22:16=0ASubject: Europa-List: d" <graeme@gdbmk.co.uk>=0A=0AI am now confused about the firewall, can I as k, is this for the tri-gear only, =0Ais it in addition to the Stainless fir ewall or instead of? Is it quicker or =0Abetter?=0ASome people seem to have used adhesive backed foil sheet over the whole area =0Aincluding surround. =0AAnd the FWFD kit includes a quantity of firewall fabric, what is that us ed for.=0A=0AI have ordered the engine and fwfd kit and just getting ready for them, I have =0Athe shiny firewall plates done.=0A=0ARegards Graeme=0A =0A--------=0AGraeme Bird=0A=0A=0A=0A=0ARead this topic online here:=0A=0Ah ttp://forums.matronics.com/viewtopic.php?p=316476#316476=0A=0A=0A=0A=0A =================




    Other Matronics Email List Services

  • Post A New Message
  •   europa-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/Europa-List.htm
  • Web Forum Interface To Lists
  •   http://forums.matronics.com
  • Matronics List Wiki
  •   http://wiki.matronics.com
  • 7-Day List Browse
  •   http://www.matronics.com/browse/europa-list
  • Browse Europa-List Digests
  •   http://www.matronics.com/digest/europa-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contribution

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --