Today's Message Index:
----------------------
1. 05:37 PM - Re: MOD 42 COLD AIR PLENUM CHAMBER for CLASSIC needed (Christoph Both)
2. 10:28 PM - Exhaust springs (Paul McAllister)
3. 11:12 PM - Re: Exhaust springs (Fred Klein)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | MOD 42 COLD AIR PLENUM CHAMBER for CLASSIC needed |
Hi Gavin:
Thank you again for your generous offer! In the mean time a builder in the
UK offered me a complete set, with all filters, etc which I took as I need
all the parts. So, for the time being I am not taking your offer. In any ca
se, thanks so much - if something breaks I will contact you!
Best,
Christoph Both
#223 Classic 912S (almost completed after 16 years)
Nova Scotia, Canada
From: owner-europa-list-server@matronics.com [mailto:owner-europa-list-serv
er@matronics.com] On Behalf Of Gavin & Anne
Sent: Friday, December 24, 2010 6:03 PM
Subject: RE: Europa-List: MOD 42 COLD AIR PLENUM CHAMBER for CLASSIC needed
Hi Chris
Not sure if you received my reply, I have a Classic plenum which you can h
ave for the cost of postage, the filter you would be able to get from the K
& N website, (not sure of the part No but someone will know) and I'm sure
someone will be able to supply you with the splash moulding to position the
intake
Contact me off list.......... gavanne@iconz.co.nz<mailto:gavanne@iconz.c
o.nz>
Merry Xmas
Gavin
________________________________
From: owner-europa-list-server@matronics.com [mailto:owner-europa-list-serv
er@matronics.com] On Behalf Of Christoph Both
Sent: Tuesday, 30 November 2010 3:26 a.m.
Subject: RE: Europa-List: MOD 42 COLD AIR PLENUM CHAMBER for CLASSIC needed
Hello,
Would anyone have a complete MOD 42 kit, 912 Rotax Plenum chamber for the C
LASSIC, and not needed any more (perhaps you upgraded to XS cowing) availab
le for purchase?
Thanks,
Christoph Both
#223
Nova Scotia, Canada
www.buildersbooks.com
http://www.matronics.com/Navigator?Europa-List
http://forums.matronics.com
rsbooks.com>
m>
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Hi all,
As some of you are aware I have been doing a few mods on my cowl. One
of the things I have done is to re design the exhaust to point
straight back. I made a temporary one out of 4130 steel to prove the
concept and I am making a new one out of stainless. I have decided to
incorporate a slip joint and I need some information on springs.
Could someone with a 912/s installation tell me the overall length,
the diameter and wire thickness of the springs that are used on there
exhaust system. Also, if there a local source then that would be
handy to know.
Thanks, Paul
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Exhaust springs |
On Dec 29, 2010, at 10:24 PM, Paul McAllister wrote:
> Could someone with a 912/s installation tell me the overall length,
> the diameter and wire thickness of the springs that are used on there
> exhaust system. Also, if there a local source then that would be
> handy to know.
Paul,
Aircraft Spruce has what they call "Rotax exhaust spring" at:
http://www.aircraftspruce.com/catalog/eppages/938-795exhaustSpring.php
66mm (2.60") hook distance. Part #938-795 Spring....2-1/4" with a
5/8" diameter.
Good Luck,
Fred
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|