Today's Message Index:
----------------------
1. 01:27 AM - Re: flap drive pin engagement (PHILLIPS I)
2. 03:48 AM - Re: flap drive pin engagement (david park)
3. 06:26 PM - Re: flap drive pin engagement (JR Gowing)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: flap drive pin engagement |
Hi Bob
the Service Bulletin is SB 16
find PDF file attached
Ivor
On 10 March 2011 23:57, JR Gowing <jrgowing@bigpond.net.au> wrote:
> David Park
>
> Would you please quote what Service Bulletin No refers, and your kit
> number so we can see if this concerns other builders?
>
>
> JR (bob) Gowing Kit no 327 in Oz
>
> Do not archive
>
> *From:* owner-europa-list-server@matronics.com [mailto:
> owner-europa-list-server@matronics.com] *On Behalf Of *david park
> *Sent:* Wednesday, 9 March 2011 1:37 AM
> *To:* europa-list@matronics.com
> *Subject:* RE: Europa-List: flap drive pin engagement
>
>
> Replaced my bearing housings with heat gun, and turned bearing with mole
> and levered with screwdriver on edge - no problem.
> Dave G-LDVO
>
> > Subject: Europa-List: flap drive pin engagement
> > From: keesdebussy@hotmail.com
> > Date: Tue, 8 Mar 2011 05:07:30 -0800
> > To: europa-list@matronics.com
> >
> keesdebussy@hotmail.com>
> >
> > In my case the flap drive pins engagement comply with the service
> bulletin on that matter but at the portside it is at the limit. So I decide
> the bring it well within the limits and I purchased the special bearing
> housing from Europa Aircraft.
> >
> > I have now a problem to remove the original housing and bearing from the
> x-tube. The x-tube end was heated with a hot air gun (air of 600 degr. C /
> 1110 degr. F) but I could not get any movement of the bearing housing.
> >
> > Has anybody experience in removeing the bearing housing from the X-tube ?
> Any ideas are welcome.
> >
> > Kees de Bussy
> > PH-SBR
> >
> >
> >
> >
> > Read this topic online here:
> >
> > http://forums.matronics.com/viewtopic.php?p=333147#333147
> >
> >
> >
> >
> >
> >===============
> >
> >
> >
>
> * *
>
> * *
>
> **
>
> **
>
> **
>
> **
>
> **
>
> *http://www.matronics.com/Navigator?Europa-List*
>
> **
>
> **
>
> *http://forums.matronics.com*
>
> **
>
> **
>
> **
>
> **
>
> *http://www.matronics.com/contribution*
>
> **
>
> * *
>
> ------------------------------
>
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 10.0.1204 / 03/09/11
>
> *
>
> *
>
>
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | flap drive pin engagement |
Bob=2C
Someone else has quoted the SB No. I changed mine during build when I had
to adjust length of cross tube.
Dave
From: jrgowing@bigpond.net.au
Subject: RE: Europa-List: flap drive pin engagement
David Park
Would you please quote what Service Bulletin No refers=2C and your kit nu
mber so we can see if this concerns other builders?
JR (bob) Gowing Kit no 327 in Oz
Do not archive
From: owner-europa-list-server@matronics.com [mailto:owner-europa-list-serv
er@matronics.com] On Behalf Of david park
Sent: Wednesday=2C 9 March 2011 1:37 AM
Subject: RE: Europa-List: flap drive pin engagement
Replaced my bearing housings with heat gun=2C and turned bearing with mole
and levered with screwdriver on edge - no problem.
Dave G-LDVO
> Subject: Europa-List: flap drive pin engagement
> From: keesdebussy@hotmail.com
> Date: Tue=2C 8 Mar 2011 05:07:30 -0800
> To: europa-list@matronics.com
>
om>
>
> In my case the flap drive pins engagement comply with the service bulleti
n on that matter but at the portside it is at the limit. So I decide the br
ing it well within the limits and I purchased the special bearing housing f
rom Europa Aircraft.
>
> I have now a problem to remove the original housing and bearing from the
x-tube. The x-tube end was heated with a hot air gun (air of 600 degr. C /
1110 degr. F) but I could not get any movement of the bearing housing.
>
> Has anybody experience in removeing the bearing housing from the X-tube ?
Any ideas are welcome.
>
> Kees de Bussy
> PH-SBR
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=333147#333147
>
>
>
>
>
>===============
>
>
> http://www.matronics.com/Navigator?Europa-Listhttp://forums.matronics.c
omhttp://www.matronics.com/contribution
No virus found in this message.
Checked by AVG - www.avg.com
Version: 10.0.1204 / 03/09/11
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | flap drive pin engagement |
Thank you Ivor!
Now I can find it in my records. I remembered the issue from what seems like
a long time ago.
I wlll now be able to put my finger on what I did.
Bob Gowing kit 327 in Oz
Do not archive
From: owner-europa-list-server@matronics.com
[mailto:owner-europa-list-server@matronics.com] On Behalf Of PHILLIPS I
Sent: Friday, 11 March 2011 8:24 PM
Subject: Re: Europa-List: flap drive pin engagement
Hi Bob
the Service Bulletin is SB 16
find PDF file attached
Ivor
On 10 March 2011 23:57, JR Gowing <jrgowing@bigpond.net.au> wrote:
David Park
Would you please quote what Service Bulletin No refers, and your kit
number so we can see if this concerns other builders?
JR (bob) Gowing Kit no 327 in Oz
Do not archive
From: owner-europa-list-server@matronics.com
[mailto:owner-europa-list-server@matronics.com] On Behalf Of david park
Sent: Wednesday, 9 March 2011 1:37 AM
Subject: RE: Europa-List: flap drive pin engagement
Replaced my bearing housings with heat gun, and turned bearing with mole and
levered with screwdriver on edge - no problem.
Dave G-LDVO
> Subject: Europa-List: flap drive pin engagement
> From: keesdebussy@hotmail.com
> Date: Tue, 8 Mar 2011 05:07:30 -0800
> To: europa-list@matronics.com
>
<keesdebussy@hotmail.com>
>
> In my case the flap drive pins engagement comply with the service bulletin
on that matter but at the portside it is at the limit. So I decide the bring
it well within the limits and I purchased the special bearing housing from
Europa Aircraft.
>
> I have now a problem to remove the original housing and bearing from the
x-tube. The x-tube end was heated with a hot air gun (air of 600 degr. C /
1110 degr. F) but I could not get any movement of the bearing housing.
>
> Has anybody experience in removeing the bearing housing from the X-tube ?
Any ideas are welcome.
>
> Kees de Bussy
> PH-SBR
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=333147#333147
>
>
>
>
>
>===============
>
>
>
http://www.matronics.com/Navigator?Europa-List
http://forums.matronics.com <http://forums.matronics.com/>
http://www.matronics.com/contribution
_____
No virus found in this message.
Checked by AVG - www.avg.com <http://www.avg.com/>
Version: 10.0.1204 / 03/09/11
arget="_blank">http://www.matronics.com/Navigator?Europa-List
ttp://forums.matronics.com
_blank">http://www.matronics.com/contribution
_____
No virus found in this message.
Checked by AVG - www.avg.com
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|