Today's Message Index:
----------------------
1. 06:26 AM - Rotax 912 Time to overhaul (Richard Lamprey)
2. 07:33 AM - Re: place for venturi -in air duct? (ptag.dev@tiscali.co.uk)
3. 09:30 AM - Re: bends for oil pipes (Steade)
4. 10:06 AM - JABIRU 3300 BRAND NEW OVER TEMPERATURE DURING TAXI (Gustavo Sessarego)
5. 12:01 PM - twillight land'g @ LAX (Fred Klein)
6. 12:25 PM - Re: JABIRU 3300 BRAND NEW OVER TEMPERATURE DURING TAXI (Peter Jeffers)
7. 05:04 PM - Re: JABIRU 3300 BRAND NEW OVER TEMPERATURE DURING TAXI (Gustavo Sessarego)
8. 05:41 PM - Re: JABIRU 3300 BRAND NEW OVER TEMPERATURE DURING TAXI (Lance Sandford)
9. 09:33 PM - Re: JABIRU 3300 BRAND NEW OVER TEMPERATURE DURING TAXI (Lance Sandford)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Rotax 912 Time to overhaul |
Does anyone have exerience running a 912UL for beyond 15 years since
first start up? The Maintenace manual says that an overhaul is
recommended after 15 years, or 1200 hrs (at least for seriel number
engine of my engine). Mine has 550 hours, after 12 years.
In UK can we run a 912UL engine beyond 15 years , 'on condition'? What
does the LSA say?
Many thanks
Richard
Kenya Europa
5Y-LRY
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: place for venturi -in air duct? |
Hi! I'll second that Gerry but do it with crimp connections, please.
(not soldered! been there got the feckin "t" shirt !
regards
Bob Harrison G-PTAG from Swedish Lapland Courtesy Ryanair and 1000
mile o/night train sleeper !
>----Original Message----
>From: gholland@content-stream.co.uk
>Date: 09/04/2011 14:09
>To: <europa-list@matronics.com>
>Subj: Re: Europa-List: place for venturi -in air duct?
>
stream.co.uk>
>
>Graeme
>Fit a TruTrak
>Gerry
>
>
>
>_-
===========================================================
>
>
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: bends for oil pipes |
Graeme
Have a look at this web site.
http://www.thinkauto.com/
Regards
David Steade
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | JABIRU 3300 BRAND NEW OVER TEMPERATURE DURING TAXI |
Hi Everybody=2C
I am Gustavo from ARGENTINA and I bought 1 year ago an Europa xs monowhell
99 % complete with jabiru 3300 brand new and airmaster 3 balde cs brand new
.
now is time to mout take the first test fly and I find out that during taxi
engine temperature is 150=B0 celcius at 1400 rpm so I richt the runway for
take off run at 190=B0 celcius so I must stop engine for proctection.
Engine Manual says 150=B0 maximun continues and 175=B0 maximun.
note: outside temperature was only 20=B0 celcius
Any advise.....?
regards from Buenos Aires -Argentina
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | twillight land'g @ LAX |
http://www.flixxy.com/twilight-landing-los-angeles-airport-cockpit-view.htm
(I prefer to kill the audio)
do not archive
Message 6
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | JABIRU 3300 BRAND NEW OVER TEMPERATURE DURING TAXI |
Hi Gustavo,
Just one silly thought. If you bought the aircraft in the States your
temperatures readouts would probably be set up in Farenheit units rather
than centigrade. Check your units.
Pete
_____
From: owner-europa-list-server@matronics.com
[mailto:owner-europa-list-server@matronics.com] On Behalf Of Gustavo
Sessarego
Sent: 10 April 2011 18:03
Subject: Europa-List: JABIRU 3300 BRAND NEW OVER TEMPERATURE DURING TAXI
Hi Everybody,
I am Gustavo from ARGENTINA and I bought 1 year ago an Europa xs
monowhell
99 % complete with jabiru 3300 brand new and airmaster 3 balde cs brand
new.
now is time to mout take the first test fly and I find out that during
taxi
engine temperature is 150=B0 celcius at 1400 rpm so I richt the runway
for
take off run at 190=B0 celcius so I must stop engine for proctection.
Engine Manual says 150=B0 maximun continues and 175=B0 maximun.
note: outside temperature was only 20=B0 celcius
Any advise.....?
regards from Buenos Aires -Argentina
_____
No virus found in this message.
Checked by AVG - www.avg.com
Message 7
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | JABIRU 3300 BRAND NEW OVER TEMPERATURE DURING TAXI |
thanks Pete=2C
I have a uMONITOR and it works on Celcius.....!!
thanks again
GUS
From: pjeffers@talktalk.net
SubjecPete=2C t: RE: Europa-List: JABIRU 3300 BRAND NEW OVER TEMPERATURE DU
RING TAXI
Hi Gustavo=2C
Just one silly thought. If you bought the aircraft in the States your temp
eratures readouts would probably be set up in Farenheit units rather than c
entigrade. Check your units.
Pete
From: owner-europa-list-server@matronics.com [mailto:owner-europa-list-serv
er@matronics.com] On Behalf Of Gustavo Sessarego
Sent: 10 April 2011 18:03
Subject: Europa-List: JABIRU 3300 BRAND NEW OVER TEMPERATURE DURING TAXI
Hi Everybody=2C
I am Gustavo from ARGENTINA and I bought 1 year ago an Europa xs monowhell
99 % complete with jabiru 3300 brand new and airmaster 3 balde cs brand new
.
now is time to mout take the first test fly and I find out that during taxi
engine temperature is 150=B0 celcius at 1400 rpm so I richt the runway for
take off run at 190=B0 celcius so I must stop engine for proctection.
Engine Manual says 150=B0 maximun continues and 175=B0 maximun.
note: outside temperature was only 20=B0 celcius
Any advise.....?
regards from Buenos Aires -Argentina http://www.matronics.com/Navigator?Eu
ropa-Listhttp://forums.matronics.comhttp://www.matronics.com/contribution
No virus found in this message.
Checked by AVG - www.avg.com
04/10/11
Message 8
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: JABIRU 3300 BRAND NEW OVER TEMPERATURE DURING TAXI |
Gustavo
Join the Jabiru Engine Matronics Forum and put your question there.
There is plenty of work being done.
Regards
Lance Sandford in OZ
On 04/11/2011 10:00 AM, Gustavo Sessarego wrote:
> thanks Pete,
>
> I have a uMONITOR and it works on Celcius.....!!
>
> thanks again
> GUS
>
> From: pjeffers@talktalk.net
> To: europa-list@matronics.com
> SubjecPete, t: RE: Europa-List: JABIRU 3300 BRAND NEW OVER TEMPERATURE
> DURING TAXI
> Date: Sun, 10 Apr 2011 20:17:43 +0100
>
> Hi Gustavo,
>
> Just one silly thought. If you bought the aircraft in the States your
> temperatures readouts would probably be set up in Farenheit units
> rather than centigrade. Check your units.
>
> Pete
>
> *From: * owner-europa-list-server@matronics.com
> [mailto:owner-europa-list-server@matronics.com] *On Behalf Of *Gustavo
> Sessarego
> *Sent:* 10 April 2011 18:03
> *To:* europa-list@matronics.com
> *Subject:* Europa-List: JABIRU 3300 BRAND NEW OVER TEMPERATURE DURING
> TAXI
>
> Hi Everybody,
>
> I am Gustavo from ARGENTINA and I bought 1 year ago an Europa xs
> monowhell 99 % complete with jabiru 3300 brand new and airmaster 3
> balde cs brand new.
>
> now is time to mout take the first test fly and I find out that during
> taxi engine temperature is 150 celcius at 1400 rpm so I richt the
> runway for take off run at 190 celcius so I must stop engine for
> proctection.
>
> Engine Manual says 150 maximun continues and 175 maximun.
>
> note: outside temperature was only 20 celcius
>
> Any advise.....?
>
> regards from Buenos Aires -Argentine
>
> *
> *
> *
> *
Message 9
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: JABIRU 3300 BRAND NEW OVER TEMPERATURE DURING TAXI |
Gustavo
Join the Jabiru Engine Matronics Forum and put your question there.
There is plenty of work being done.
Regards
Lance Sandford in OZ
On 04/11/2011 10:00 AM, Gustavo Sessarego wrote:
> thanks Pete,
>
> I have a uMONITOR and it works on Celcius.....!!
>
> thanks again
> GUS
>
> From: pjeffers@talktalk.net
> To: europa-list@matronics.com
> SubjecPete, t: RE: Europa-List: JABIRU 3300 BRAND NEW OVER TEMPERATURE
> DURING TAXI
> Date: Sun, 10 Apr 2011 20:17:43 +0100
>
> Hi Gustavo,
>
> Just one silly thought. If you bought the aircraft in the States your
> temperatures readouts would probably be set up in Farenheit units
> rather than centigrade. Check your units.
>
> Pete
>
> *From: * owner-europa-list-server@matronics.com
> [mailto:owner-europa-list-server@matronics.com] *On Behalf Of *Gustavo
> Sessarego
> *Sent:* 10 April 2011 18:03
> *To:* europa-list@matronics.com
> *Subject:* Europa-List: JABIRU 3300 BRAND NEW OVER TEMPERATURE DURING
> TAXI
>
> Hi Everybody,
>
> I am Gustavo from ARGENTINA and I bought 1 year ago an Europa xs
> monowhell 99 % complete with jabiru 3300 brand new and airmaster 3
> balde cs brand new.
>
> now is time to mout take the first test fly and I find out that during
> taxi engine temperature is 150 celcius at 1400 rpm so I richt the
> runway for take off run at 190 celcius so I must stop engine for
> proctection.
>
> Engine Manual says 150 maximun continues and 175 maximun.
>
> note: outside temperature was only 20 celcius
>
> Any advise.....?
>
> regards from Buenos Aires -Argentina
>
> *
> *
> *
> *
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|