Today's Message Index:
----------------------
1. 01:03 AM - Re: Fuel Tank Capacity (Bob Harrison)
2. 01:59 AM - Europa fuel tank capacity (John Greenhalgh)
3. 08:34 AM - Re: Door wedges??? (AirEupora)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Fuel Tank Capacity |
Hi! Tim
I have to question your statement that the "two tank bottoms either side of
the saddle totalling 18 litres" means 9 litres in the reserve. It is my
belief that the starboard side is the smaller of the two sides so only an
actual measure will provide the correct reserve amount? Either way it is
best not assumed but remove any doubt by doing a measure.
Regards
Bob Harrison G-PTAG
-----Original Message-----
From: owner-europa-list-server@matronics.com
[mailto:owner-europa-list-server@matronics.com] On Behalf Of Tim Ward
Sent: 06 May 2011 23:11
Subject: Re: Europa-List: Fuel Tank Capacity
John,
I have a total capacity 65.5 litres, 18 litres is the total amount in the
two compartments either side of the saddles, which means
9 litres reserve. There is a further 2 litres up the fuel intake corbra etc.
Tim
Tim Ward,
12 Waiwetu Street,
Fendalton,
Christchurch 8052
New Zealand
Ph; 03 3515166
Mob; 0210640221
email; ward.t@xtra.co.nz
-----Original Message-----
From: John Greenhalgh
Sent: Saturday, May 07, 2011 9:37 AM
Subject: Europa-List: Fuel Tank Capacity
<john.greenhalgh1@sky.com>
I'm in the process of calibrating my fuel tank and would like to know
what the reserve tank capacity and the overall tank capacity including
the reserve.
Any information would be much appreciated.
Regards John
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Europa fuel tank capacity |
I'm in the process of calibrating my fuel tank and would like to know
what the reserve tank capacity and the overall tank capacity including
the reserve.
Any information would be much appreciated.
Regards John
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Door wedges??? |
I took some clay to see if I could make the wedges and figured out that I had put
the wide MOD 67 panel on wrong. It was off center. So I took it off to re-center.
I had to do some fiberglass repairs as this was the second time I had
installed and removed it. Because of the wide MOD 67 the door is weak in the
middle and you can see it bowed there. I took a piece of aluminum angle on
the outside and was thinking of heating it up and determined that I needed more
strength in this area. I laid three layers of one inch tape and shaped it into
an L around a aluminum angle inside the door area above the lower lip. I
made it about 18 inches long. I believe that will straighten the door in this
area. I will be added some more fiberglass to the cut out areas from the wide
MOD 67. I'll let you know the results in a few days.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=339188#339188
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|