Today's Message Index:
----------------------
1. 06:31 AM - Re: 1st time Hose replacement: R914 turbo, XS Trigear (h&jeuropa)
2. 10:02 AM - Re: Re: 1st time Hose replacement: R914 turbo, XS Trigear (Alan Burrill)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: 1st time Hose replacement: R914 turbo, XS Trigear |
Here is a link to a good article about hose replacement.
http://www.rotax-owner.com/rotax-blog/item/21-rotax-5-year-rubber-replacement-the-installation-considerations
Part 1 is on the same website.
Most of us use fuel injection hose because it seems to contain gasoline smell better
than other hose but it is difficult to fit because it is so stiff. The
new carburetor hose mentioned in the article contains the smell and is easy to
fit. You will need 3/8 dia hose to go from the pumps to the engine and return
to the tank. Roughly 2 10ft runs and an additional 10ft to connect to selector
valve and filters. You will also need some 1/4 hose for fuel tank drains,
probably no more than 10 feet. The fittings on the engine are metric and fit
5/16 hose. We use 3/8 to 5/16 reducers and short pieces of 5/16 hose for this.
For water hoses, the fittings on the Rotax are 17 mm and we have not found English
dimension hose that fits correctly. It is difficult to purchase 17mm hose.
We ended up getting hose from Rotax. We used 2 Rotax 922 250 hoses. The
Europa supplied hose from the water pump has a tight 180 degree bend that is difficult
to find in an automotive hose. We purchase that hose from Europa and
use automotive hose from the expansion tank to the radiator.
Many owners use the silicon water hoses advertised in the Europa Club Flyer.
We use ThermoSleeve on all our hoses. This is the material on the hoses from Rotax.
You can purchase it high performance automotive suppliers.
Hope this helps you plan.
Jim & Heather
N241BW
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=426488#426488
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: 1st time Hose replacement: R914 turbo, XS Trigear |
I have just done mine and the following links supplied all of the
materials i used including hoses, cable clamps and stainless steel tie
wraps for the Fireproof sleeves.
http://www.firesleeveandtape.com
http://www.hcl-clamping.co.uk
http://www.hoseworld.com
http://www.simtag.co.uk/aircraft
I used ISO standard fuel hose which is specified and is fire resistant,
I tried to set a piece alight using and blowtorch and failed! I still
used fire sleeve over the fuel hoses and the myclick clamps to affix in
place as they gave a low profile able to go under the fire sleeve.
The only silicon I used was the two water pump hoses and I got them from
Europa. All the other water hoses are the 17mm rubber.
Alan
G-OBJT
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=426488#426488
>
>
>
>
>
>
>
>
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|