Europa-List Digest Archive

Mon 03/02/15


Total Messages Posted: 2



Today's Message Index:
----------------------
 
     1. 09:00 PM - Oil Hose (Martin Tuck)
     2. 11:08 PM - Re: Oil Hose (Alan Burrill)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 09:00:54 PM PST US
    From: Martin Tuck <MJKTuck@cs.com>
    Subject: Oil Hose
    Hi All, I'm looking to replace my oil hoses. The one from the pump to the radiator has a 90 deg bend in it. I had noted that it was suggested I contact Lockwood as they have a metal 90 deg adapter to which regular hose could be fitted. I contacted them and they said just to use 'an AN fitting size -8'. Looking at the manual though the thread seems to be 14.4mm so I'm not sure what they meant now. I wonder if they meant to make a 90 deg elbow using AN fittings. I couldn't figure the parts I would need though. Any help as to what others have done would be appreciated. Also, are there any US sources for the rubber engine mounts or are they uniquely Europa, in which case I would contact the factory in the UK. Regards, Martin Tuck N152MT Wichita, KS


    Message 2


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 11:08:49 PM PST US
    Subject: Re: Oil Hose
    From: Alan Burrill <alanb@dpy01.co.uk>
    Replaced mine last year and used normal oil hose with no bends and no 90 deg bend on the pump. route of hose work ok without any kinks or tight bends. Alan G-OBJT > On 3 Mar 2015, at 04:59, Martin Tuck <MJKTuck@cs.com> wrote: > > > Hi All, > > I'm looking to replace my oil hoses. The one from the pump to the radiator has a 90 deg bend in it. I had noted that it was suggested I contact Lockwood as they have a metal 90 deg adapter to which regular hose could be fitted. I contacted them and they said just to use 'an AN fitting size -8'. Looking at the manual though the thread seems to be 14.4mm so I'm not sure what they meant now. I wonder if they meant to make a 90 deg elbow using AN fittings. I couldn't figure the parts I would need though. > > Any help as to what others have done would be appreciated. > > Also, are there any US sources for the rubber engine mounts or are they uniquely Europa, in which case I would contact the factory in the UK. > > Regards, > Martin Tuck > N152MT > Wichita, KS > > > >




    Other Matronics Email List Services

  • Post A New Message
  •   europa-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/Europa-List.htm
  • Web Forum Interface To Lists
  •   http://forums.matronics.com
  • Matronics List Wiki
  •   http://wiki.matronics.com
  • 7-Day List Browse
  •   http://www.matronics.com/browse/europa-list
  • Browse Europa-List Digests
  •   http://www.matronics.com/digest/europa-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contribution

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --