Today's Message Index:
----------------------
1. 12:56 AM - Re: Europa-List Digest: 2 Msgs - 03/27/15 (Peter & Anthea Austin)
2. 02:56 PM - Ring mount to engine (William Daniell)
3. 04:08 PM - Re: Ring mount to engine (Keith Hickling)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Europa-List Digest: 2 Msgs - 03/27/15 |
___________________________ Message 2
_____________________________________
>
>
> Time: 05:31:50 PM PST US
> Subject: Europa-List: Skyforce GPS
> From: "Alan Carter" <alancarteresq@onetel.net>
>
> I experienced the same problem, traced to the Skyforce antenna wire,
my GPS sits above my Radio (Becker)
> and the coiled up Antenna wire had moved close to the Radio. wrapped
the coil in tin foil put it above the GPS and attached it to the
underside of the Panel, problem solved.
Hope this helps.
Peter
ZK-ZEB
> Hi, All.
> Have the standard GPS installation in my Europa, and I am getting a
constant timed
> flash of interference coming through the head set.
>
> Switch the GPS OFF and the flash of interference stops,
>
> Pull the unit out of its housing by about 3 inches with it turned on
and the interference
> has gone,
>
> What is causing this constant timed flash of interference.
>
> 1.If I can fix the cause of it,
> 2.How can I shield the GPS unit from picking this signal up,
> As I said pull the unit away from its housing by about 3 " and its
gone.
>
> Regards.
> Alan
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=439968#439968
>
>
>
>
>
>
>
>
>
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Ring mount to engine |
Im am fitting the ring mount to engine. There is a lot of stuff in the
way...for example coolant hoses to the cylinder heads and some of the
wiring.
I dont want to remove any more than I have to. What needs to be removed in
order to fit the ring mount? For example does one need to remove the
starter motor?
Thanks in advance
Will
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Ring mount to engine |
Hi William,
If it=99s a 912 you are fitting, here is a comprehensive reply
from Bud Yearly when I asked the same question. Note the issue of the
lower coolant hoses and changing the angle of one of the lower coolant
hose nozzles from the water pump while you have it off. All not too
difficult when you remove the right bits. I didn=99t have to
remove the starter motor.
Good luck!
Regards,
Keith Hickling
New Zealand.
From: William Daniell
Sent: Sunday, March 29, 2015 10:55 AM
Subject: Europa-List: Ring mount to engine
Im am fitting the ring mount to engine. There is a lot of stuff in the
way...for example coolant hoses to the cylinder heads and some of the
wiring.
I dont want to remove any more than I have to. What needs to be removed
in order to fit the ring mount? For example does one need to remove the
starter motor?
Thanks in advance
Will
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|