Today's Message Index:
----------------------
1. 02:39 AM - Re: Re: radio interferance (danny shepherd)
2. 10:56 AM - Wrapping composite aircraft (William Daniell)
3. 01:36 PM - Re: Wrapping composite aircraft (bryannortje)
4. 02:53 PM - Re: Wrapping composite aircraft (spcialeffects)
5. 10:27 PM - Re: Wrapping composite aircraft (=?utf-8?Q?Gert_Dalgaard_S=C3=B8rensen?=)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: radio interferance |
Hi Ira,
Thanks for your input. I trailed RI back home from the
airfield so I can work on her in comfort :-) . hopefully I will be able
to sort the problem.
Cheers Danny. G- c.e.r.i.
On 15/09/2015 18:47, rampil wrote:
>
> It is nearly impossible to remotely diagnose this problem without wiring diagrams,
photos of the install, etc. Generically, grounding is a possibility.
>
> So, did you check all the resistance values of ground pins on the radio
> and the case all the way back to the engine block or negative battery
> terminal with a quality ohm meter? All should certainly be less than 0.5
> ohms. Generically, there should be no ground loops, all grounds go to
> a single point in the panel, then to the other side of the firewall.
>
> Good luck!
>
> --------
> Ira N224XS
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=447092#447092
>
>
> -----
> No virus found in this message.
> Checked by AVG - www.avg.com
>
>
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Wrapping composite aircraft |
Has anyone wrapped a Europa?
I have not yet been able to find anyone with experience of finishing a
composite aircraft in Bogota so I was thinking that this might be an
interesting alternative.
Thanks
Will
William Daniell
LONGPORT
+57 310 295 0744
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Wrapping composite aircraft |
We did our previous aircraft a Skyranger Nynja very successfully and our Europa
will soon be getting a similar treatment. I have attached a photo for you to
drool over....
--------
Europa Owner / Builder and Passionate about Flying
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=447170#447170
Attachments:
http://forums.matronics.com//files/thumb_img_1561_1024_668.jpg
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Wrapping composite aircraft |
Hi William. If you google it and trawl through the image results I'm sure there
is a piece on a yellow Europa which has been wrapped.
Frank Xuereb kit#165
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=447173#447173
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Wrapping composite aircraft |
Have been flying a wrapped Europa for 10 years - no problem :)
Regards
Gert
OY-GDS / Mono / 914
> Den 17/09/2015 kl. 19.56 skrev William Daniell
<wdaniell.longport@gmail.com>:
>
> Has anyone wrapped a Europa?
>
> I have not yet been able to find anyone with experience of finishing a
composite aircraft in Bogota so I was thinking that this might be an
interesting alternative.
>
> Thanks
>
> Will
>
>
> William Daniell
> LONGPORT
> +57 310 295 0744
>
>
<http://www.matronics.com/Navigator?Europa-List>
<http://www.matronics.com/contribution>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|