Today's Message Index:
----------------------
0. 09:13 AM - What Are You Thankful For...? (Matt Dralle)
1. 01:30 AM - Re: Re: Altitude Hold kit. Trio. (roddyeuropa@aol.com)
2. 01:50 AM - Re: Re: Altitude Hold kit. Trio. (david park)
3. 02:04 AM - Re: Re: Altitude Hold kit. Trio. (roddyeuropa@aol.com)
Message 0
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | What Are You Thankful For...? |
Dear Listers,
Here in the United States, Thursday is our National day of Thanksgiving. Many
of us will be traveling to be with our families and friends to share in generous
feasts of plenty and giving thanks for the many blessings that have been bestowed
upon us.
Many Listers have expressed over the last couple of weeks how thankful they are
for the Email Lists and Forums here on the Matronics servers and for all of the
assistance and comradery they have experienced being a part of the Lists.
One of my favorite comments is when someone writes to me and says something like,
"Its the first thing I do in the morning while I'm having my morning coffee!".
That's a wonderful tribute to the purpose and function of these Lists.
Its always great to hear I'm not the only one that jumps out of bed each morning
to check my List email!!
Won't you take a minute today and show your appreciation for these Lists and for
their continued operation and upgrade?
The List Contribution Site is:
http://www.matronics.com/contribution
Or, drop a personal check in the mail to:
Matt Dralle / Matronics
581 Jeannie Way
Livermore CA 94550
USA
Thank you in advance for your kind consideration,
Matt Dralle
Matronics Email List Administrator
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Altitude Hold kit. Trio. |
I did this mod a couple of years back and used the original CS10 torque tube, and
had the europa supplied lugs welded on by a local specialist aircraft welder.
I preferred to keep the original control system as much the same as possible.
Getting the lugs welded on was not the hardest part - its a lot of work to
get the torque tube out, and also very fiddly to connect the new servo rod - there
is just so little room to work.
In answer to your question "I just want to confirm that the Alt. Hold horn is exactly
the same orientation as the Stabilator port horn" I'm pretty sure that
the horn is not the same orientation, but the drawings in mod 76 show the correct
position. The position is vital - I made a jig to hold it in place so there
was no question of the welder putting it in the wrong place. So good luck!
Roddy Kesterton
G-IKRK
-----Original Message-----
From: david park <dpark748@icloud.com>
Sent: Tue, 24 Nov 2015 23:16
Subject: Re: Europa-List: Re: Altitude Hold kit. Trio.
Europa supply a kit to modify the CS10 by welding the two horns onto the CS10 to
take the pushrod from the servo.
Dave
Sent from my iPhone
> On 24 Nov 2015, at 22:12, graeme bird <graeme@gdbmk.co.uk> wrote:
>
>
> Have you replaced cs10 then ? How easy was it?
> It sounds like you are adding horns to the existing.
>
> --------
> Graeme Bird
> G-UMPY
> Mono Classic/XS FFW 912S/Woodcomp 3000/3W
> Newby: 200 hours 4 years on the Mono
> g(at)gdbmk.co.uk
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=450192#450192
>
>
>
>
>
>
>
>
>
>
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Altitude Hold kit. Trio. |
Just to be certain, i only want to do this once!!!!
Did you translate the angle from the drawings on Mod 76.
Dave
Sent from my iPhone
> On 25 Nov 2015, at 09:28, roddyeuropa@aol.com wrote:
>
> I did this mod a couple of years back and used the original CS10 torque tu
be, and had the europa supplied lugs welded on by a local specialist aircraf
t welder. I preferred to keep the original control system as much the same a
s possible. Getting the lugs welded on was not the hardest part - its a lot o
f work to get the torque tube out, and also very fiddly to connect the new s
ervo rod - there is just so little room to work.
> In answer to your question "I just want to confirm that the Alt. Hold horn
is exactly the same orientation as the Stabilator port horn" I'm pretty sur
e that the horn is not the same orientation, but the drawings in mod 76 show
the correct position. The position is vital - I made a jig to hold it in pl
ace so there was no question of the welder putting it in the wrong place. So
good luck!
> Roddy Kesterton
> G-IKRK
>
>
>
> -----Original Message-----
> From: david park <dpark748@icloud.com>
> To: europa-list <europa-list@matronics.com>
> Sent: Tue, 24 Nov 2015 23:16
> Subject: Re: Europa-List: Re: Altitude Hold kit. Trio.
>
>
> Europa supply a kit to modify the CS10 by welding the two horns onto the C
S10 to take the pushrod from the servo.
> Dave
>
> Sent from my iPhone
>
>
> > On 24 Nov 2015, at 22:12, graeme bird <graeme@gdbmk.co.uk> wrote:
> >
> >
> > Have you replaced cs10 then ? How easy was it?
> > It sounds like you are adding horns to the existing.
> >
> > --------
> > Graeme Bird
> > G-UMPY
> > Mono Classic/XS FFW 912S/Woodcomp 3000/3W
> > Newby: 200 hours 4 years on the Mono
> > g(at)gdbmk.co.uk
> >
> >
> >
> >
> > Read this topic online here:
> >
> > http://forums.matronics.com/viewtopic.php?p=450192#450192
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
>
>
>
>
>
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Altitude Hold kit. Trio. |
I think so, but it was a while ago. I think I set it up with the angles shown and
then checked that there was sufficient movement full forward and back, and
that there was no danger of 'over centre', the real no no. And yes, you wouldn't
want to do this mod too many times!
Roddy.
-----Original Message-----
From: david park <dpark748@icloud.com>
Sent: Wed, 25 Nov 2015 9:50
Subject: Re: Europa-List: Re: Altitude Hold kit. Trio.
Just to be certain, i only want to do this once!!!!
Did you translate the angle from the drawings on Mod 76.
Dave
Sent from my iPhone
On 25 Nov 2015, at 09:28, roddyeuropa@aol.com wrote:
I did this mod a couple of years back and used the original CS10 torque tube, and
had the europa supplied lugs welded on by a local specialist aircraft welder.
I preferred to keep the original control system as much the same as possible.
Getting the lugs welded on was not the hardest part - its a lot of work to
get the torque tube out, and also very fiddly to connect the new servo rod - there
is just so little room to work.
In answer to your question "I just want to confirm that the Alt. Hold horn is exactly
the same orientation as the Stabilator port horn" I'm pretty sure that
the horn is not the same orientation, but the drawings in mod 76 show the correct
position. The position is vital - I made a jig to hold it in place so there
was no question of the welder putting it in the wrong place. So good luck!
Roddy Kesterton
G-IKRK
-----Original Message-----
From: david park <dpark748@icloud.com>
Sent: Tue, 24 Nov 2015 23:16
Subject: Re: Europa-List: Re: Altitude Hold kit. Trio.
Europa supply a kit to modify the CS10 by welding the two horns onto the CS10 to
take the pushrod from the servo.
Dave
Sent from my iPhone
> On 24 Nov 2015, at 22:12, graeme bird <graeme@gdbmk.co.uk> wrote:
>
>
> Have you replaced cs10 then ? How easy was it?
> It sounds like you are adding horns to the existing.
>
> --------
> Graeme Bird
> G-UMPY
> Mono Classic/XS FFW 912S/Woodcomp 3000/3W
> Newby: 200 hours 4 years on the Mono
> g(at)gdbmk.co.uk
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=450192#450192
>
>
>
>
>
>
>
>
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|