Europa-List Digest Archive
Thu 05/26/16 |
Total Messages Posted: 2 |
Today's Message Index:
----------------------
1. 04:02 AM - Tail plane torque tube assembly tips needed (Graeme Hart)
2. 11:39 PM - Re: Tail plane torque tube assembly tips needed (Alasdair Milne)
Message 1
INDEX Back to Main INDEX
NEXT Skip to NEXT Message
LIST Reply to LIST Regarding this Message
SENDER Reply to SENDER Regarding this Message
Time: 04:02:28 AM PST US
Subject: Tail plane torque tube assembly tips needed
From: Graeme Hart <graeme.hart@onecoolkat.com>
Hi All
I am about to assemble my tail plane torque tube for the first time and
need some advice. This is from an approximately 1999 vintage Trigear XS
kit if that affects the answer.
I have pictures showing the torque tube assembled on a bench by a previous
owner so I know the parts fit together.
The parts such as TP12 and TP9 are an extremely tight fit over the tube TP4.
During summer I managed to partially install TP12 on the end of TP4. This
was after the parts had been sitting in the car and they were quite warm.
This makes me think heat may be part of the answer. I don't know the
temperature they reached but it could have been up to 35 degrees C from the
car but more likely about 25.
Now when I try to remove TP12 it won't budge.
I'd appreciate any suggestions or advice from those who have done it before.
Thanks
Graeme
Message 2
INDEX Back to Main INDEX
PREVIOUS Skip to PREVIOUS Message
NEXT Skip to NEXT Message
LIST Reply to LIST Regarding this Message
SENDER Reply to SENDER Regarding this Message
Time: 11:39:38 PM PST US
From: "Alasdair Milne" <milneab@btinternet.com>
Subject: Tail plane torque tube assembly tips needed
Hi Graeme,
My kit around 2000 I had the same problem. I spent a long time trying
to lap the outer parts for the tailplanes to the tube. I think that is
possible but I gave up and got a replacement tube from Europa. I
believe that kit was No 517 or thereabouts.
Alasdair
From: owner-europa-list-server@matronics.com
[mailto:owner-europa-list-server@matronics.com] On Behalf Of Graeme Hart
Sent: 26 May 2016 12:02
Subject: Europa-List: Tail plane torque tube assembly tips needed
Hi All
I am about to assemble my tail plane torque tube for the first time and
need some advice. This is from an approximately 1999 vintage Trigear XS
kit if that affects the answer.
I have pictures showing the torque tube assembled on a bench by a
previous
owner so I know the parts fit together.
The parts such as TP12 and TP9 are an extremely tight fit over the tube
TP4.
During summer I managed to partially install TP12 on the end of TP4.
This
was after the parts had been sitting in the car and they were quite
warm.
This makes me think heat may be part of the answer. I don't know the
temperature they reached but it could have been up to 35 degrees C from
the
car but more likely about 25.
Now when I try to remove TP12 it won't budge.
I'd appreciate any suggestions or advice from those who have done it
before.
Thanks
Graeme
Other Matronics Email List Services
Post A New Message    europa-list@matronics.com
UN/SUBSCRIBE    http://www.matronics.com/subscription
List FAQ    http://www.matronics.com/FAQ/Europa-List.htm
Web Forum Interface To Lists    http://forums.matronics.com
Matronics List Wiki    http://wiki.matronics.com
7-Day List Browse    http://www.matronics.com/browse/europa-list
Browse Europa-List Digests    http://www.matronics.com/digest/europa-list
Browse Other Lists    http://www.matronics.com/browse
Live Online Chat!    http://www.matronics.com/chat
Archive Downloading    http://www.matronics.com/archives
Photo Share    http://www.matronics.com/photoshare
Other Email Lists    http://www.matronics.com/emaillists
Contributions    http://www.matronics.com/contribution
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --