Europa-List Digest Archive

Wed 07/13/16


Total Messages Posted: 3



Today's Message Index:
----------------------
 
     1. 01:34 AM - Re: Torque Tube enhancement after 400 hours (GBWFH2010)
     2. 01:59 AM - Re: Re: Torque Tube enhancement after 400 hours (kjburns@btinternet.com)
     3. 12:09 PM - Re: Re: Torque Tube enhancement after 400 hours (ami-mcfadyean@talktalk.net)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 01:34:43 AM PST US
    Subject: Re: Torque Tube enhancement after 400 hours
    From: "GBWFH2010" <gaxuk2001@gmail.com>
    I had the same problem after doing the Loctite 'mod' and had slightly more movement than your tailplane (after 300 hours). My inspector took advice from the LAA who stated remedial action had to be taken prior to Permit renewal. I decided I could not keep going trough this hassle so took the decision to do one of the torque tube clamping mods. I chose the one offered by Pat Tunney, whose help and assistance was superb, but I think Bob Harrison has also designed a very good mod. It was a swine of a job to do but I am really pleased with the results and after 200 hours there is no sign of any movement. Hope this helps. -------- Gordon Grant G-BWFH Read this topic online here: http://forums.matronics.com/viewtopic.php?p=458119#458119


    Message 2


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 01:59:34 AM PST US
    Subject: Re: Torque Tube enhancement after 400 hours
    From: kjburns@btinternet.com
    When building the torque tube up the ream the holes to interference fit ... Or you will get movement . There is an oversize limit to how big you can take the pins if you get it wrong , but custom pins can be oversized (only up to that limit )to save your bacon, any movement built in will increases in service . 300 +hours on reamed / custom pins and no play ....advice taken from Andy Draper UK laa /one of the original Europa production engineers. Regards Kevin Sent from my iPhone > On 13 Jul 2016, at 10:32, GBWFH2010 <gaxuk2001@gmail.com> wrote: > > > I had the same problem after doing the Loctite 'mod' and had slightly more movement than your tailplane (after 300 hours). My inspector took advice from the LAA who stated remedial action had to be taken prior to Permit renewal. > > I decided I could not keep going trough this hassle so took the decision to do one of the torque tube clamping mods. I chose the one offered by Pat Tunney, whose help and assistance was superb, but I think Bob Harrison has also designed a very good mod. It was a swine of a job to do but I am really pleased with the results and after 200 hours there is no sign of any movement. > > Hope this helps. > > -------- > Gordon Grant > > G-BWFH > > > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=458119#458119 > > > > > > > > > >


    Message 3


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 12:09:17 PM PST US
    From: "ami-mcfadyean@talktalk.net" <ami-mcfadyean@talktalk.net>
    Subject: Re: Torque Tube enhancement after 400 hours
    Same method (interference fit of the Factory oversize pins) worked for me too. About 500hours now since it was done. My Permit Inspector thinks there's a little within-tolerance play, but actually that's the small clearance in the torque tube bearings; I'd rather those bearings had some clearance than being tight, which they can be if not concentrically aligned. Duncan McF. ----Original Message---- From: kjburns@btinternet.com Subj: Re: Europa-List: Re: Torque Tube enhancement after 400 hours When building the torque tube up the ream the holes to interference fit ... Or you will get movement . There is an oversize limit to how big you can take the pins if you get it wrong , but custom pins can be oversized (only up to that limit )to save your bacon, any movement built in will increases in service . 300 +hours on reamed / custom pins and no play ....advice taken from Andy Draper UK laa /one of the original Europa production engineers. Regards Kevin Sent from my iPhone > On 13 Jul 2016, at 10:32, GBWFH2010 <gaxuk2001@gmail.com> wrote: > > > I had the same problem after doing the Loctite 'mod' and had slightly more movement than your tailplane (after 300 hours). My inspector took advice from the LAA who stated remedial action had to be taken prior to Permit renewal. > > I decided I could not keep going trough this hassle so took the decision to do one of the torque tube clamping mods. I chose the one offered by Pat Tunney, whose help and assistance was superb, but I think Bob Harrison has also designed a very good mod. It was a swine of a job to do but I am really pleased with the results and after 200 hours there is no sign of any movement. > > Hope this helps. > > -------- > Gordon Grant > > G-BWFH > > > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=458119#458119 > > > > > > > > > >




    Other Matronics Email List Services

  • Post A New Message
  •   europa-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/Europa-List.htm
  • Web Forum Interface To Lists
  •   http://forums.matronics.com
  • Matronics List Wiki
  •   http://wiki.matronics.com
  • 7-Day List Browse
  •   http://www.matronics.com/browse/europa-list
  • Browse Europa-List Digests
  •   http://www.matronics.com/digest/europa-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contribution

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --