---------------------------------------------------------- Europa-List Digest Archive --- Total Messages Posted Thu 12/01/16: 3 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 02:51 PM - Trip report Gower Beaches South Wales UK (graeme bird) 2. 06:45 PM - 10 inch Dynon in a Mono (Martin Tuck) 3. 07:57 PM - Re: 10 inch Dynon in a Mono (Fred Klein) ________________________________ Message 1 _____________________________________ Time: 02:51:54 PM PST US Subject: Europa-List: Trip report Gower Beaches South Wales UK From: "graeme bird" https://forums.flyer.co.uk/viewtopic.php?f=67&t=102407 -------- Graeme Bird G-UMPY - Mono Classic/XS FFW 912S, Woodcomp 3000/3W CS, trutrak Gemini 2 axis ap, pflarm, ads-b out, 8.33khz, mode S, FP 5, Aera500 & SD on Nexus, 250 hours & 4 years on the Mono, 880 total g(at)gdbmk.co.uk Read this topic online here: http://forums.matronics.com/viewtopic.php?p=463614#463614 ________________________________ Message 2 _____________________________________ Time: 06:45:36 PM PST US From: Martin Tuck Subject: Europa-List: 10 inch Dynon in a Mono Hi, I'm still determined to upgrade my Europa monowheel to an EFIS and have pretty much settled on the 10 inch Dynon display. So I'm in my early stages of panel planning I have determined that the standard mono panel moulding is not quite wide enough for the 10 in screen. It needs building up to the left by maybe 1/2 inch which starts to encroach into the recess for the gear/flap handle. My question is, has anyone else already done this and if so, did you make some kind of gear/flap handle extension that would make it easier to push and pull the handle up and down? I'd be interested in any solutions along with any pictures. Thanks, Martin Tuck Wichita, Kansas ________________________________ Message 3 _____________________________________ Time: 07:57:18 PM PST US From: Fred Klein Subject: Re: Europa-List: 10 inch Dynon in a Mono Martinthough I opted for the 7=9D Skyview, principally because I have a stand-alone EMS and will not have to split-screen the Dynon to get that data, because of associated layout decisions regarding back up steam gauges, I too needed to decrease the width of the recess for the gear/flap handle by approx. 1/2=9Da bit of handy hacksaw work is all it tookI=99ll send pixs directly to youFred > On Dec 1, 2016, at 6:44 PM, Martin Tuck wrote: > > I'm still determined to upgrade my Europa monowheel to an EFIS and have pretty much settled on the 10 inch Dynon display. > > So I'm in my early stages of panel planning I have determined that the standard mono panel moulding is not quite wide enough for the 10 in screen. > > It needs building up to the left by maybe 1/2 inch which starts to encroach into the recess for the gear/flap handle. ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message europa-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Europa-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/europa-list Browse Digests http://www.matronics.com/digest/europa-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.