Today's Message Index:
----------------------
1. 12:59 AM - Re: Aileron balancing (Bob Harrison)
2. 01:33 AM - Re: MOD sheets? (Peter Jeffers)
3. 05:49 AM - Re: Aileron balancing (William Daniell)
4. 07:23 AM - Re: Aileron balancing (Bob Harrison)
5. 07:41 AM - Re: Aileron balancing (William Daniell)
6. 10:25 AM - Re: MOD sheets? (Neville Eyre)
7. 10:34 AM - Re: Aileron balancing (Bob Harrison)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Aileron balancing |
Hi! William .
Have you painted them yet ?
Regards
Bob H G-PTAG
From: owner-europa-list-server@matronics.com
[mailto:owner-europa-list-server@matronics.com] On Behalf Of William
Daniell
Sent: 12 March 2017 01:39
Subject: Europa-List: Aileron balancing
Dear all
I drilled a 1/4 hole in each aileron weight with very little effect.
The hinges are free amd i dont think im doing anything wrong.
Is this normal? What next? 1/2" hole?
Help please.
Will
No virus found in this message.
Checked by AVG - www.avg.com <http://www.avg.com/email-signature>
03/12/17
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Hi Clive,
If you really want them I could email them to you but their applicability to
your a/c is largely dependent upon whether your kit is classic or XS.
I have left a voice message on your mobile with my phone number if you wish
to talk about it.
Pete Jeffers Europa Club LAA Inspector
-----Original Message-----
From: owner-europa-list-server@matronics.com
[mailto:owner-europa-list-server@matronics.com] On Behalf Of clivesutton
Sent: 11 March 2017 17:12
Subject: Europa-List: MOD sheets?
--> <clive.maf@googlemail.com>
Hi, on the final inspection prep run now and checking off each required MOD
with the LAA list against what's on the a/c.
But can't find anything on the EC or Europa websites for the following MOD's
- Does anyone have/can send me, copies please?
MOD 15 - FWD Lift Pin Fuselage Strengthening MOD 16 - Shock Absorber Block
Shape MOD 17 - Rudder Pedal guides
MOD46 - Pitch Torque Tube End Cap
clive.maf@googlemail.com
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=467178#467178
-----
No virus found in this message.
Checked by AVG - www.avg.com
---
This email has been checked for viruses by AVG.
http://www.avg.com
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Aileron balancing |
Yes i have
Will
On Mar 12, 2017 04:02, "Bob Harrison" <ptag.dev@tiscali.co.uk> wrote:
> Hi! William .
>
> Have you painted them yet ?
>
> Regards
>
> Bob H G-PTAG
>
>
> *From:* owner-europa-list-server@matronics.com [mailto:owner-europa-list-
> server@matronics.com] *On Behalf Of *William Daniell
> *Sent:* 12 March 2017 01:39
> *To:* europa-list@matronics.com
> *Subject:* Europa-List: Aileron balancing
>
>
> Dear all
>
>
> I drilled a 1/4 hole in each aileron weight with very little effect. The
> hinges are free amd i dont think im doing anything wrong.
>
>
> Is this normal? What next? 1/2" hole?
>
>
> Help please.
>
>
> Will
>
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 03/12/17
>
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Aileron balancing |
William. If you were to compare the volume /weight removed between
=C2=BC=9D hole to a =C2=BD=9D hole the difference would be
huge. So small bits but often is the order of the plan. Then you have to
fill the holes with some foam and glass it over and repaint . Quite a
lot of patience needed to complete it !
Regards
Bob Harrison G-PTAG
From: owner-europa-list-server@matronics.com
[mailto:owner-europa-list-server@matronics.com] On Behalf Of William
Daniell
Sent: 12 March 2017 12:49
Subject: RE: Europa-List: Aileron balancing
Yes i have
Will
On Mar 12, 2017 04:02, "Bob Harrison" <ptag.dev@tiscali.co.uk> wrote:
Hi! William .
Have you painted them yet ?
Regards
Bob H G-PTAG
From: owner-europa-list-server@matronics.com
[mailto:owner-europa-list-server@matronics.com] On Behalf Of William
Daniell
Sent: 12 March 2017 01:39
Subject: Europa-List: Aileron balancing
Dear all
I drilled a 1/4 hole in each aileron weight with very little effect.
The hinges are free amd i dont think im doing anything wrong.
Is this normal? What next? 1/2" hole?
Help please.
Will
No virus found in this message.
Checked by AVG - www.avg.com
Version: 03/12/17
No virus found in this message.
Checked by AVG - www.avg.com <http://www.avg.com/email-signature>
03/12/17
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Aileron balancing |
Ok thanks...so from the pic in the manual we are talking level suspended
from the hinge underside uppermost....right?
Will
On Mar 12, 2017 09:26, "Bob Harrison" <ptag.dev@talktalk.net> wrote:
> William. If you were to compare the volume /weight removed between =C2
=BC=9D
> hole to a =C2=BD=9D hole the difference would be huge. So small bi
ts but often is
> the order of the plan. Then you have to fill the holes with some foam and
> glass it over and repaint . Quite a lot of patience needed to complete i
t !
>
> Regards
>
> Bob Harrison G-PTAG
>
>
> *From:* owner-europa-list-server@matronics.com [mailto:owner-europa-list-
> server@matronics.com] *On Behalf Of *William Daniell
> *Sent:* 12 March 2017 12:49
> *To:* europa-list@matronics.com
> *Subject:* RE: Europa-List: Aileron balancing
>
>
> Yes i have
>
> Will
>
>
> On Mar 12, 2017 04:02, "Bob Harrison" <ptag.dev@tiscali.co.uk> wrote:
>
> Hi! William .
>
> Have you painted them yet ?
>
> Regards
>
> Bob H G-PTAG
>
>
> *From:* owner-europa-list-server@matronics.com [mailto:owner-europa-list-
> server@matronics.com] *On Behalf Of *William Daniell
> *Sent:* 12 March 2017 01:39
> *To:* europa-list@matronics.com
> *Subject:* Europa-List: Aileron balancing
>
>
> Dear all
>
>
> I drilled a 1/4 hole in each aileron weight with very little effect. The
> hinges are free amd i dont think im doing anything wrong.
>
>
> Is this normal? What next? 1/2" hole?
>
>
> Help please.
>
>
> Will
>
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 03/12/17
>
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 03/12/17
>
Message 6
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Hi Clive,
Hope this goes through, my posts have gone MIA before
Mod 15, the ''top hat'' lay up of 3 Bids over 3'' x 1/4'' blue foam, vertical from
door sill to thigh support, centred over lift socket.
Mod 16, original block was a rectangular ''brick'', needs a V cutting out of upper
and lower faces [ bear to do, get a new one from Europa].
Mod 17, without my notes can't be sure, might be the 5/8'' tubes [CS31] Reduxed
into the pedal pivot tubes ?
Mod 46 Pitch torque tube originally had the solid bearings [ as per aileron control
system] replaced with a spherical [ self aligning] bearing and beefier cap.
All these were very early on.
Tip, when you submit the paperwork to LaaLaaLand, list EVERY MOD, and mark as N/A
as [ for instance] a Trigear application will be returned if the mono wheel
block, Mod 16 hasn't been done..... DOH !
Cheers,
Nev
-----Original Message-----
From: clivesutton <clive.maf@googlemail.com>
Sent: Sat, 11 Mar 2017 19:55
Subject: Europa-List: MOD sheets?
Hi, on the final inspection prep run now and checking off each required MOD with
the LAA list against what's on the a/c.
But can't find anything on the EC or Europa websites for the following MOD's -
Does anyone have/can send me, copies please?
MOD 15 - FWD Lift Pin Fuselage Strengthening
MOD 16 - Shock Absorber Block Shape
MOD 17 - Rudder Pedal guides
MOD46 - Pitch Torque Tube End Cap
clive.maf@googlemail.com
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=467178#467178
Message 7
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Aileron balancing |
Hi! William,
I haven=99t a manual handy but that sounds about right .
Regards
Bob H
From: owner-europa-list-server@matronics.com
[mailto:owner-europa-list-server@matronics.com] On Behalf Of William
Daniell
Sent: 12 March 2017 14:39
Subject: RE: Europa-List: Aileron balancing
Ok thanks...so from the pic in the manual we are talking level suspended
from the hinge underside uppermost....right?
Will
On Mar 12, 2017 09:26, "Bob Harrison" <ptag.dev@talktalk.net> wrote:
William. If you were to compare the volume /weight removed between
=C2=BC=9D hole to a =C2=BD=9D hole the difference would be
huge. So small bits but often is the order of the plan. Then you have to
fill the holes with some foam and glass it over and repaint . Quite a
lot of patience needed to complete it !
Regards
Bob Harrison G-PTAG
From: owner-europa-list-server@matronics.com
[mailto:owner-europa-list-server@matronics.com] On Behalf Of William
Daniell
Sent: 12 March 2017 12:49
Subject: RE: Europa-List: Aileron balancing
Yes i have
Will
On Mar 12, 2017 04:02, "Bob Harrison" <ptag.dev@tiscali.co.uk> wrote:
Hi! William .
Have you painted them yet ?
Regards
Bob H G-PTAG
From: owner-europa-list-server@matronics.com
[mailto:owner-europa-list-server@matronics.com] On Behalf Of William
Daniell
Sent: 12 March 2017 01:39
Subject: Europa-List: Aileron balancing
Dear all
I drilled a 1/4 hole in each aileron weight with very little effect.
The hinges are free amd i dont think im doing anything wrong.
Is this normal? What next? 1/2" hole?
Help please.
Will
No virus found in this message.
Checked by AVG - www.avg.com
Version: 03/12/17
No virus found in this message.
Checked by AVG - www.avg.com
Version: 03/12/17
No virus found in this message.
Checked by AVG - www.avg.com <http://www.avg.com/email-signature>
03/12/17
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|