Today's Message Index:
----------------------
1. 12:42 AM - Re: IMC night application - propeller (ami-mcfadyean@talktalk.net)
2. 01:08 AM - Rivet squeezer (Richard Iddon)
3. 02:26 AM - Re: Rivet squeezer (davidjoyce@doctors.org.uk)
4. 03:28 AM - Nevs Funeral (david park)
5. 07:10 AM - Re: Rivet squeezer (Ivor)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: IMC night application - propeller |
<<..Has anyone seen any damage from rain.>>
Not on Warp Drive blades with metal LE protection, which are sold as being suitable
for seaplanes.
Arplast (which don't take kindly to LE protection) is another matter and a (2-pack)
paint film comes off pretty quickly.
Does clean the bugs off too!
Duncan McF
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
I am replacing the pads on my tri gear. I have got the new pads & rivets from the
factory but it seems I need a rivet squeezer to fit them. I have had a look
on the LAS web site but am confused as to which tool I need. Does anyone have
the correct tool which I could borrow or can I do the job with a hammer & punch?
Richard Iddon
G-RIXS
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Rivet squeezer |
Richard, I have always managed with a drift held in a vice on one side &
hammer & punch other side David Joyce, GXSDJ , N of Stockholm)
On 2017-06-03 09:07, Richard Iddon wrote:
>
> I am replacing the pads on my tri gear. I have got the new pads & rivets from
the factory but it seems I need a rivet squeezer to fit them. I have had a look
on the LAS web site but am confused as to which tool I need. Does anyone have
the correct tool which I could borrow or can I do the job with a hammer & punch?
>
> Richard Iddon
>
> G-RIXS
Links:
------
[1] http://www.matronics.com/Navigator?Europa-List
[2] http://forums.matronics.com
[3] http://wiki.matronics.com
[4] http://www.matronics.com/contribution
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Is anyone going from Manchester just had problem with my car.
I live near Manchester Airport, Heald Green.
Dave Park
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Rivet squeezer |
Ritchard
i have the correct tool but as David said the correct size punch and vice
is adequate to do the job,
but if you want me to send it too you then PM me with your address and i
will get it in the post,
Ivor
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=469808#469808
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|