Today's Message Index:
----------------------
0. 04:28 AM - LOC (Matt Dralle)
1. 03:35 AM - Re: lock-wiring 912 sump banjo bolt (Nigel Graham)
2. 03:52 AM - Re: lock-wiring 912 sump banjo bolt (Nigel Graham)
3. 05:32 AM - Re: order of assembly for cooling duct, radiators and hoses (h&jeuropa)
4. 05:45 AM - Re: Re: order of assembly for cooling duct, radiators and hoses (Rowland Carson)
5. 03:32 PM - Re: lock-wiring 912 sump banjo bolt (Rowland_Carson)
6. 04:08 PM - Re: Re: lock-wiring 912 sump banjo bolt (Rowland Carson)
Message 0
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Dear Listers,
Each year at the end of the List Fund Raiser, I post a message acknowledging everyone
that so generously made a Contribution to support the Lists. Its sort
of my way of publicly thanking everyone that took a minute to show their appreciation
for the Lists.
Won't you take a moment and assure that your name is on that List of Contributors
(LOC)? As a number of members have pointed out over the years, the List seems
at least - if not a whole lot more - valuable as a building/flying/recreating/entertainment
tool as your typical magazine subscription!
Please take minute and assure that your name is on this year's LOC! Show others
that you appreciate the Lists. Making a Contribution to support the Lists is
fast and easy using your Credit card or Paypal on the Secure Web Site:
http://www.matronics.com/contribution
or by popping a personal check in the mail to:
Matronics Email Lists
c/o Matt Dralle
581 Jeannie Way
Livermore CA 94550
I would like to thank everyone that has so generously made a Contribution thus
far in this year's List Fund Raiser! Remember that its YOUR support that keeps
these Lists going and improving! Don't forget to include a little comment about
how the Lists have
helped you!
Best regards,
Matt Dralle
Email List Administrator
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: lock-wiring 912 sump banjo bolt |
Richard is correct - in fact there are two holes !
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=485225#485225
Attachments:
http://forums.matronics.com//files/wirelock_hole_148.jpg
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: lock-wiring 912 sump banjo bolt |
........................at the front, and one at the rear.
.... good recovery I thought ;-)
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=485226#485226
Attachments:
http://forums.matronics.com//files/wirelock_hole_rear_137.jpg
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: order of assembly for cooling duct, radiators and hoses |
Rowland,
We just took the engine (914) and factory cowl/duct off our XS for maintenance,
so got reacquainted with the sequence.
We mount the oil cooler in the duct first. It is on spacers so it sits low.
Attach the duct with the bolts to the footwells, so it is located but can still
pivot on those.
Attach the oil lines to the cooler. Access to the fittings is good.
Install the coolant radiator. It will need washers for spacers on the sides.
We use a product called Stick It temporary adhesive (its a sticky adhesive but
heavy grease would work too) to hold the washers in place. The radiator mounts
up high in the duct. We added a drain fitting on the bottom port side of
the radiator. It makes it a lot easier and less mess when subsequently removing
the radiator.
Swing the duct into place and attach the coolant hoses. Use clamps with hex screws
and you can reach them with a long extension. We reach the clamps from the
port side.
Attach the side plates (CD4 & CD5) to the footwells and secure the duct with the
side bolts. Be sure you have nutplates on the interior of the duct for these.
With the factory setup it is important that all the air entering the duct goes
through the radiators; there can be no air leaks. We use aluminum tape, rubber
strips and weather stripping. We even tape between the bottom of the coolant
radiator and the top of the oil cooler.
We fit Thermo Shield on all hoses.
Jim & Heather
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=485305#485305
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: order of assembly for cooling duct, radiators and |
hoses
On 2018-11-19, at 13:31, h&jeuropa <butcher43@att.net> wrote:
> We just took the engine (914) and factory cowl/duct off our XS for maintenance,
so got reacquainted with the sequence.
Jim - thats all very useful advice, thanks, and supports my own tentative thoughts
on the process.
in friendship
Rowland
| Rowland Carson ... that's Rowland with a 'w' ...
| <rowlandcarson@gmail.com> http://www.rowlandcarson.org.uk
| Skype, Twitter: rowland_carson Facebook: Rowland Carson
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: lock-wiring 912 sump banjo bolt |
[quote="Richard Wheelwright"]
There should be a small hole along the sump seam close to the banjo. There is on
my engine
[/quote]
And there is on mine too! How did I miss that when I first looked???
Thanks for the advice and for not calling me an idiot!
in friendship
Rowland
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=485319#485319
Message 6
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: lock-wiring 912 sump banjo bolt |
On 2018-11-19, at 23:31, Rowland_Carson <rowil@clara.net> wrote:
[snip]
Dont know how the Matronics list still has that e-mail address - it stopped being
used many years ago - so please dont use it. Its <rowlandcarson@gmail.com>
to reach me now.
in friendship
Rowland
| Rowland Carson ... that's Rowland with a 'w' ...
| <rowlandcarson@gmail.com> http://www.rowlandcarson.org.uk
| Skype, Twitter: rowland_carson Facebook: Rowland Carson
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|