Today's Message Index:
----------------------
1. 10:06 AM - Airmaster spinner forward bulkhead/disc rattling? (JonathanMilbank)
2. 10:36 AM - Airmaster spinner forward disc/bulkhead secure? (JonathanMilbank)
3. 10:40 AM - Airmaster spinner front bulkhead/disc snug fit? (JonathanMilbank)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Airmaster spinner forward bulkhead/disc rattling? |
That spinner bulkhead, the grey disc on the front of the black cylindrical housing,
very often doesn't fit tightly/firmly/snugly enough into the actual spinner
and there is a small gap of maybe 0,1 mm between the grey plastic disc and
the inside of the metal spinner.
After many hours of use, when you take the spinner off for some reason, you might
find grey powder/dust inside the spinner and a witness mark inside the spinner
where the grey plastic disc rubs against it.
So I usually wrap a few (3 or 4?) short lengths (5 cm each?) of electrical insulation
tape across the edge of the plastic disc at equal intervals around the
edge of the disc, before putting the spinner back on.
How does anyone know if there is a gap? If the spinner goes on too easily before
inserting the screws which attach it to the rear bulkhead/ disc, then there
is probably a small gap. So if there are first a few pieces of tape around the
edge of the front grey plastic disc, then a small push against the front of the
spinner is needed before it is possible to insert the fastening screws in the
rear bulkhead.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=489087#489087
Attachments:
http://forums.matronics.com//files/airmaster_spinner_5_156.jpg
http://forums.matronics.com//files/airmaster_spinner_4_131.jpg
http://forums.matronics.com//files/airmaster_spinner_3_475.jpg
http://forums.matronics.com//files/airmaster_spinner_2_864.jpg
http://forums.matronics.com//files/airmaster_spinner_1_425.jpg
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Airmaster spinner forward disc/bulkhead secure? |
That spinner bulkhead, the grey disc on the front of the black cylindrical housing,
very often doesn't fit tightly/firmly/snugly enough into the actual spinner
and there is a small gap of maybe 0.1 mm / a few thou between the grey plastic
disc and the inside of the metal spinner.
After many hours of use, when you take the spinner off for some reason, you might
find grey powder/dust inside the spinner and a witness mark inside the spinner
where the grey plastic disc rubs against it.
So I usually wrap a few short lengths (3 inches each?) of electrical insulation
tape across the edge of the plastic disc at equal intervals around the edge of
the disc, before putting the spinner back on.
How does anyone know if there is a gap? If the spinner goes on too easily before
inserting the screws which attach it to the rear bulkhead/ disc, then there
is probably a small gap. So if there are firstly a few pieces of tape stuck around
the edge of the front grey plastic disc, then a small push against the front
of the spinner is needed before it is possible to insert the fastening screws
in the rear bulkhead.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=489088#489088
Attachments:
http://forums.matronics.com//files/airmaster_spinner_1_112.jpg
http://forums.matronics.com//files/airmaster_spinner_2_146.jpg
http://forums.matronics.com//files/airmaster_spinner_3_921.jpg
http://forums.matronics.com//files/airmaster_spinner_4_113.jpg
http://forums.matronics.com//files/airmaster_spinner_5_620.jpg
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Airmaster spinner front bulkhead/disc snug fit? |
That spinner bulkhead, the grey disc on the front of the black cylindrical housing,
very often doesn't fit tightly/firmly/snugly enough into the actual spinner
and there is a small gap of maybe 0.1 mm / a few thou between the grey plastic
disc and the inside of the metal spinner.
After many hours of use, when you take the spinner off for some reason, you might
find grey powder/dust inside the spinner and a witness mark inside the spinner
where the grey plastic disc rubs against it.
So I usually wrap a few short lengths (3 inches each?) of electrical insulation
tape across the edge of the plastic disc at equal intervals around the edge of
the disc, before putting the spinner back on.
How does anyone know if there is a gap? If the spinner goes on too easily before
inserting the screws which attach it to the rear bulkhead/ disc, then there
is probably a small gap. So if there are firstly a few pieces of tape stuck around
the edge of the front grey plastic disc, then a small push against the front
of the spinner is needed before it is possible to insert the fastening screws
in the rear bulkhead.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=489089#489089
Attachments:
http://forums.matronics.com//files/airmaster_spinner_5_201.jpg
http://forums.matronics.com//files/airmaster_spinner_4_163.jpg
http://forums.matronics.com//files/airmaster_spinner_3_155.jpg
http://forums.matronics.com//files/airmaster_spinner_2_123.jpg
http://forums.matronics.com//files/airmaster_spinner_1_121.jpg
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|